Trailer Hub Seal for a Hub with Inner Bearing L44643

Question

Question:

I need to replace the rear hub seal on my boat trailer. the hub is a 5 lug and the rear bearing that I replaced is an L44643. Is that enough info to help me find what Im looking for.

asked by: Jimmy P

0

Expert Reply:

The matching race for bearing # L44643 is # L44610. For this race and bearing combination the seal is # RG06-010. It has an inner diameter of 1.249 inches and an outer diameter of 1.983 inches. This is a set of double lip seals that provide a much better seal than a single lip.

If the L44643 bearing was the outer bearing then I will need to know the inner bearing to determine the correct seal.

expert reply by: Michael H

0

Answer 1

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 2

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

view full answer...

Answer 3

Dutton-Lainson Hand Winch #DL11001 does not come with a cable because they want to leave the options open for people to choose the size and length that works best for them. As-is this winch can accept a 7/32 inch cable up to 82 feet long or a 1/4…

view full answer...

Answer 4

Thanks for the photo. The Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,500 lbs #DL14825 you asked the question from is set-up much differently. The style of winch you have is more like a worm gear winch #DL11001. The…

view full answer...

Answer 5

No, the 1.063" ID #L44649 bearings cannot replace the 1.00" ID #L44643 bearings as they are too large like you mentioned; you'll need to use the #L44643.

view full answer...

Answer 6

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 7

The seal you need is going to be more associated with the inner bearing and race. The outer bearing will help identify other parts but only if I have both bearing numbers. If both bearings are the same then the seal is #34823 or for a pair use…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Trailer Hub Seal for a Hub with Inner Bearing L44643

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching