What Style of Hand Winch Can be Powred In and Out with Power Drill

Question

Question:

Hand winch question: I need a hand winch to pull/slide a 2000lb pallet the length of a semitrailer 50 feet a few pallets a week.. I would like one that could be operated with a cordless drill and be able to pull the cable out so not a worm gear winch. Suggestions ? Thanks

asked by: e

1

Helpful Expert Reply:

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part # DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

expert reply by: Jameson C

1

Gary

7/6/2020

I want a 2500 lb winch that can use cable and use a drill with brake system? Witch one is it?

Chris R.

7/9/2020

The highest rated winch we have that can be used with a drill like this is the 2,000 pound # DL11001 mentioned above.

Gary

7/10/2020

@ChrisR it is the Dutton Lainson DLB 2500 a . You have to buy the Drill kit extra ?

Answer 1

Dutton-Lainson Hand Winch #DL11001 does not come with a cable because they want to leave the options open for people to choose the size and length that works best for them. As-is this winch can accept a 7/32 inch cable up to 82 feet long or a 1/4…

view full answer...

Answer 2

Thanks for the photo. The Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,500 lbs #DL14825 you asked the question from is set-up much differently. The style of winch you have is more like a worm gear winch #DL11001. The…

view full answer...

Answer 3

The seal you need is going to be more associated with the inner bearing and race. The outer bearing will help identify other parts but only if I have both bearing numbers. If both bearings are the same then the seal is #34823 or for a pair use…

view full answer...

Answer 4

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 5

No, the 1.063" ID #L44649 bearings cannot replace the 1.00" ID #L44643 bearings as they are too large like you mentioned; you'll need to use the #L44643.

view full answer...

Answer 6

The matching race for bearing #L44643 is #L44610. For this race and bearing combination the seal is #RG06-010. It has an inner diameter of 1.249 inches and an outer diameter of 1.983 inches. This is a set of double lip seals that provide a much…

view full answer...

Answer 7

The dimensions for the Dutton-Lainson Worm Gear Hand Winch #DL11001 are as follows: Height including hand crank: 12-1/4 inches Length of side panel: 5-1/2 inches Height of side panel: 4-1/4 inches Width of base: 4-3/4 inches

view full answer...

Answer 8

The instructions for the #DL11011 state, "to minimize heat build up and possible winch damage, do not exceed 600 rpm." So, although you can use a drill with the Dutton-Lainson Drill Drive Socket Adapter for DLB Series Winches #DL6456 to…

view full answer...

Answer 9

The main benefit of a worm gear winch like the Dutton-Lainson Hand Winch part #DL10970 over a brake winch like the Dutton-Lainson Hand Winch part #DL74FR is that worm gear winches don't have a minimum load requirement. If you're consistently…

view full answer...

Answer 10

We have winches that can have power drills attached to them to make cranking a bit easier. For this, you'd want something like the Dutton Lainson Worm Gear Winch #DL11004 which does have the hex drive option.

view full answer...

Answer 11

Since the Dutton-Lainson Worm Gear Hand Winch #DL11011 that you referenced is a worm gear winch, there really isn't a way to quickly unspool the cable. To extend the line you would turn the handle one direction, and then to retract the line you…

view full answer...

Answer 12

The Dutton-Lainson DL2000 is indeed different as it is an earlier model of the DL2000A; I checked with Dutton-Lainson and they do not offer replacement parts for the older DL2000, and said that parts are not interchangeable between models. So while I…

view full answer...

What Style of Hand Winch Can be Powred In and Out with Power Drill

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching