Torque Wrench Recommendation for Installing Trailer Hitch

Question

Question:

Hi, I just received my hitch and want to install it by myself basically DIY. I read that we need to have a torque wrench for the specified torque for the nuts. What are the good options for torque wrench that i can buy? There are too many options on the internet and are confusing. Thanks in advance

asked by: Rupi

0

Expert Reply:

We offer a nice 100 ft/lb capacity 3/8 inch drive torque wrench from Performance Tools that's rated for 10-100 foot lbs as part # PT87ZR, but unless you regularly do automotive work you might be better off borrowing a wrench from a friend or neighbor. Some auto parts sores will loan or rent tools, which is a good alternative.

A beam-type torque wrench like # PTW3001C would be a less expensive alternative, but I'd personally avoid those as they're not terribly accurate.

expert reply by: Mike L

0

Answer 1

Hey Barry congrats on the new SUV! The hitches for the 2025 Infiniti QX60 like item #C46DR are going to block the range of the sensors around the center of your bumper where the 2" receiver sits. You'll need to kick to the left and right to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hi Cameron! For your 2025 Mazda 3 Sedan, I prefer the Curt #C44DR over the Draw-Tite #24982. They are almost identical and have the same weight capacities, but Curt is made in America and Draw-Tite is not. This pretty much always pushed me to the…

view full answer...

Answer 4

Hey Keith, thanks for the information! If your 2021 Jeep Grand Cherokee Laredo X has the removable rear fascia to hide the factory hitch, I recommend the Draw-Tite Max-Frame Hitch item #DT38MR. This is comparable in design and capacity to the factory…

view full answer...

Answer 5

Hi Michael! The amount of work involved really depends on how your truck is set up. If your truck has a factory hitch, that will need to be removed before installing a new one. In that case, I’d recommend going with the Curt Class 5 Hitch #C15005.…

view full answer...

Answer 6

Hey Jukius, we do have the Rhino Rack ROC25 roof rack part #RR56RR as a confirmed fit for your 2010 Volkswagen Golf City. This would be what I would recommend for your vehicle. What are you planning on carrying with this rack?

view full answer...

Answer 7

The most hidden trailer hitch available for your 2020 Dodge Durango is without a doubt the Draw-Tite Max-Frame Trailer Hitch Receiver #DT38MR. The 2" receiver for this Class III hitch will actually extend out through the bottom of the rear…

view full answer...

Answer 8

Hi Joe; just like the Curt #C96NR, the Draw-Tite Max-Frame Trailer Hitch Receiver #DT42GR does not allow for a 20" spare tire. However, we do have the Blue Ox Trailer Hitch Receiver #BLU46HR. I just reached out to Blue Ox and they said it will…

view full answer...

Answer 9

For the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" #C12172, there really isn't a solution other than to use a torque wrench. Without torqing the necessary bolts to the manufacturer specs, you void the warranty and can have…

view full answer...

Answer 10

Yes, the Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 will work with the Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier part #TH665C. The weld nut inside the shank on the Thule Transporter is the same as that on the…

view full answer...

Torque Wrench Recommendation for Installing Trailer Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching