Ventline Exterior Wall Vent for RV Range Hood

Question

Question:

My 2013 trailer has a Jensen 29-762 range vent, I want to replace it without drilling new holes in w

asked by: Blaine M

0

Expert Reply:

I suggest the Ventline Exterior Wall Vent for RV Range Hood, # V2111-03 for a very easy DIY install.

expert reply by: Michael R

0

Answer 1

The dimensions of Ventline Exterior Wall Vent for RV Range Hood #V2111-03 are shown in the linked photo I prepared for you. Mounting hole spacing is also indicated. Overall edge to edge dimensions are 5-1/4 x 11-5/8-inches and the vent fits an RV…

view full answer...

Answer 2

Trailer makers rarely keep track of smaller items like vent parts used in fabrication of their trailers so finding the right replacement part is often just a matter of measuring, as you have done. Since we do have this item in stock, Ventline…

view full answer...

Answer 3

To install the Ventline Exterior Wall Vent #V2111-13 that you referenced you will need 10 screws and sealant which is sold separately. You can use the TremPro 644 Silicone Sealant part #0160297 and 10 of part #31071 for the installation. An…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Ventline Exterior Wall Vent for RV Range Hood

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching