Parts Needed to Install the Ventline Exterior Wall Vent # V2111-13

Question

Question:

Is anything needed to install part V2111-13.

asked by: Nancy

0

Expert Reply:

To install the Ventline Exterior Wall Vent # V2111-13 that you referenced you will need 10 screws and sealant which is sold separately.

You can use the TremPro 644 Silicone Sealant part # 0160297 and 10 of part # 31071 for the installation.

An installation video has been linked for you to check out.

expert reply by: Jon G

0

Answer 1

Trailer makers rarely keep track of smaller items like vent parts used in fabrication of their trailers so finding the right replacement part is often just a matter of measuring, as you have done. Since we do have this item in stock, Ventline…

view full answer...

Answer 2

I suggest the Ventline Exterior Wall Vent for RV Range Hood, #V2111-03 for a very easy DIY install.

view full answer...

Answer 3

The dimensions of Ventline Exterior Wall Vent for RV Range Hood #V2111-03 are shown in the linked photo I prepared for you. Mounting hole spacing is also indicated. Overall edge to edge dimensions are 5-1/4 x 11-5/8-inches and the vent fits an RV…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 6

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 10

Hello Lee, thanks for reaching out. If air won't go in at all it could be a bad/clogged valve. You could also have a major leak somewhere. Have you tried a soap test to see if there are any leaks?

view full answer...

Answer 11

Hey Michael! The 2026 Kia Sportage Hybrid has the 12V battery integrated into the main battery so you won't be making a connection there. What you need to do is run the #C59236 hot lead to the 12V positive jump terminal under the hood. Everything…

view full answer...

Answer 12

For your Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter - Lippert 1621 and 0719 - 20,000 lbs #RP94720 you will need the Air System Service Kit for Reese Goose Box 5th Wheel to Gooseneck Air Ride Coupler Adapter #RP86007 which will…

view full answer...

Parts Needed to Install the Ventline Exterior Wall Vent # V2111-13

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching