Can SuperSprings TSS-107-40 Trailer Suspension Helper Springs Be Cut Down if Too Tall to Fit

Question

Question:

I bought the sumo spring TSS-106-40 for my trailer and found out that it’s too tall to install. Is it safe to cut the sumo spring in half to make it fit.

asked by: Chris K

0

Expert Reply:

According to the folks in the engineering department at SuperSprings, the manufacturer of SumoSprings it is acceptable to cut down the SumoSprings if necessary, but be aware that doing so will void the product warranty. SuperSprings recommends cutting as little as possible off the springs.

expert reply by: Mike L

0

Answer 1

Thank you for reaching out! The best thing for your situation is to go with the 3,500 lb Dexter Axle #T3584F-8974 you are looking at. While you can upgrade your axles to the 5,200 lb #e55GR, you won't really see a benefit from it unless you also…

view full answer...

Answer 2

The SumoSprings Solo Custom Helper Springs like part #SSR-209-40 can be in contact with the jounce spring contact point without a load present. Depending on which kit you have, there is sometimes a spacer that will allow you to have either a slight…

view full answer...

Answer 3

The best option to lift your trailer with 3,500 lbs axles is definitely going to be the Dexter Trailer Springs Over-Under Conversion Kit #K71-384-00. The reason for that is it is going to give you the most clearance, because it moves your…

view full answer...

Answer 4

Hey Tom, if you are going to trim down the SumoSprings kit part #TSS-107-40 you would want to trim off the top of the spring.

view full answer...

Answer 5

Adding suspension to your trailer is definitely beneficial as it helps to reduce stress on the frame. The most common type of suspension system for a trailer is one that uses leaf springs. To install this you would need a hanger kit like part #APS4…

view full answer...

Answer 6

Trailer suspension U-bolt plates can bend, yes, so it doesn't sound like you have anything to worry about. For 3/8 inch nuts on the U-bolts in kit #APUBR-10 they should be torqued between 30 and 50 foot pounds according to Dexter Axle.

view full answer...

Answer 7

It sounds like you installed leaf springs that weren't the correct length for your setup. Looking at your equalizer it looks like your springs are too long. The simplest solution would be to have your front and rear suspension hangers removed and…

view full answer...

Answer 8

The SumoSprings Trailer Helper Springs #SS33HR is designed for applications where the leaf springs are under the axle - if you only have 4-1/2" of spacing between the top of the leaf spring stack and your trailer frame then that leads me to…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can SuperSprings TSS-107-40 Trailer Suspension Helper Springs Be Cut Down if Too Tall to Fit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching