Recommended Bearing Buddy Bra For Bearing Buddies W/ 2.38" Outside Diameter

Question

Question:

2.38 outside diameter bearing buddy, i need covers please

asked by: James R

0

Expert Reply:

For your Bearing Buddies that have an outside diameter of 2.38" you will need the Replacement Bearing Buddy Bras - Model 23B - (Pair) # BB23B which will be a nice snug fit.

I included a video of the # BB23B for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Hello Alan, thanks for reaching out. We do carry the 1.25" ID seals like part #TMK56ZR, but I am sorry to say we do not offer a wear sleeve in this size. We carry a few wear sleeves from Bearing Buddy, but sadly, they do not make anything that…

view full answer...

Answer 2

The Trailer Hub Assembly #8-258-50UC1-EZ does appear to be the correct replacement hub assembly for your 2007 Tracker Trailstar Trailer. To confirm this you will want to remove the entire hub assembly and ensure the spindle is a straight spindle and…

view full answer...

Answer 3

Hello Jeff, Thank you for the picture, they are always most helpful. That is an interesting set-up. It looks like it might be an old o-ring from a Dexter Vault like the Dexter Vault Hybrid Lubrication System for 2,500-lb to 3,500-lb Trailer Buddy…

view full answer...

Answer 4

The replacement wet bolt you need for an EZ Flex kit like your trailer has is the part #34007-187-00, the correct bushing is #D014-077-00, and if you need nuts too it's part #006-007-01.

view full answer...

Answer 5

Yes, the Kodiak Trailer Idler Hub Assembly #Q-HUB84545 that you referenced is perfectly compatible with EZ lube spindles. The only difference between the hubs that are EZ lube and non-EZ lube is the cap style. So for an EZ lube style cap that fits…

view full answer...

Answer 6

We do not have spindle wear sleeves available for individual sale. Since you have the Dexter #84545BX you can use the Bearing Buddy Spindle Grease Seal Set for LM48548 or L68149 Inner Bearing #BB60002. This includes a stainless steel sleeve for the…

view full answer...

Answer 7

It might be Dan but I wasn't able to pull any specific information off of the UFP 13674 part number you gave me. What you'll need to do is pull one of the hubs and read the part numbers stamped into the sides of the bearings. This information…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 10

Hey Bill, no the 84 spindle part #TRU74FR does not require a wear sleeve of any type with the grease seal. Did you bend or damage a spindle?

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Recommended Bearing Buddy Bra For Bearing Buddies W/ 2.38" Outside Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching