Can the Mounting Height of the Dutton-Lainson Square Swivel Jack Be Adjusted

Question

Question:

Do you know if the height on this jack can be adjusted up and down on the mount similar to the Fulton jack. I cant swing the jack down on my Boatmate trailer due to the driveway angle and would like to see if I can raise the mount position Upinch on the trailer frame to gain some swing downinch height. Again...this is the position on where it is mounted on the trailer frame...not the adjustability using the crank.

asked by: Ken V

0

Expert Reply:

The bolt-on frame bracket for the Dutton-Lainson Square Swivel Jack part # DL22340 is welded to the outer tube so no, it cannot be adjusted. I think a better option would be the Fulton XLT Bolt-Thru Swivel Trailer Jack part # F26ZR since the bolt-on frame brackets sit lower on the jack tube which provides more ground clearance.

expert reply by: Conner L

0

Answer 1

I have included a dimensional drawing of the Dutton-Lainson Round Swivel Jack #DL22335 that shows the overall extended height of the jack at 40-5/8" tall. This measurement is from the bottom of the wheel to the top of the jack when extended.

view full answer...

Answer 2

The Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR TruTurn 360-degree caster doesn't run on a bearing and the wheel only has a standard bolt. According to Fulton, the TruTurn only means that it is capable of rotating 360 degrees. For a swivel…

view full answer...

Answer 3

In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and this…

view full answer...

Answer 4

The Fulton F2 trailer jack #F1413230134 can get pretty low. I went out to the warehouse and pulled one of these jacks to measure it. The mounting bracket is adjustable so with it in the lowest position from the bottom of the foot to the bottom of the…

view full answer...

Answer 5

Hey Rod, The Ark Xtreme Off-Road Jack w/ 2 Wheels #ARK99FR has multiple slots in the outer tube of the jack that the mounting bracket can slot into. In the bottom slot you'd be right around 9-1/2" between the ground and frame with the wheels…

view full answer...

Answer 6

I was able to get the following image information from ARK for their Xtreme Off-Road Swivel Trailer Jack #ORJW750BD which shows the different lengths for the jack in the storage position depending on which setting you have it in. The overall length…

view full answer...

Answer 7

The body lift definitely complicated getting a gooseneck hitch installed as the rails for the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit #BWGNRK1059 will attach directly to the frame of your truck. As i am sure…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs, #FXP15W will work for your application. A similar jack like the Fulton XLT Bolt-Thru Swivel Trailer Jack - Weld On - Sidewind - 12" Lift - 1,500 lbs,…

view full answer...

Answer 10

Most likely the #FXP15W would work great as a replacement for what you have but it's hard to verify that without seeing how what you have now mounts to the trailer. If you could send me a picture of what you have I can verify.

view full answer...

Answer 11

I have the perfect replacement trailer jack for your 2006 Mastercraft X-Star boat trailer. For this, I recommend using the Fulton F2 Swing-Up, Wide-Track Trailer Jack part #F1413050334. It has a 1,600 lb. capacity and can raise your boat trailer up…

view full answer...

Answer 12

We do not have a replacement gear for your Shelby Model 5850GF swivel jack, unfortunately, so you'd need a replacement jack instead. The Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR is a bolt on swivel jack designed for utility and marine…

view full answer...

Can the Mounting Height of the Dutton-Lainson Square Swivel Jack Be Adjusted

Product Page this Question was Asked From

Continue Researching