Ground Clearance Using Fulton F2 Swivel Trailer Jack with Pivoting Footplate

Question

Question:

I would like to know the distance from the bottom of the bracket where it would bolt to the trailer and the base of the foot.

asked by: Eric L

0

Expert Reply:

The Fulton F2 trailer jack # F1413230134 can get pretty low. I went out to the warehouse and pulled one of these jacks to measure it.

The mounting bracket is adjustable so with it in the lowest position from the bottom of the foot to the bottom of the u-bolt hole using the small u-bolt measures 3-7/8 inches. With the bracket all the way up it is 17 inches.

If using the larger u-bolt is measures 3-1/8 inches from bottom of foot to bottom of lower mounting hole. And In the highest position it measures 16-7/16 inches. I have included a picture and video with the measurements.

expert reply by: Michael H

0

click to enlarge

Answer 1

I spoke with my contact at Fulton, and the retracted height of the #F1413230134 jack from bottom of foot to center of mounting plate would be 5-3/8 inches when the bracket is at the lowest setting. When the bracket is slid to the highest setting, the…

view full answer...

Answer 2

I went out to our warehouse to take a look at the Fulton F2 Swing-Up Jack #F1413230134 referenced in your question. With the jack fully retracted, I measured a distance of right at 25 inches from the bottom of the footplate to the top of the jack.…

view full answer...

Answer 3

The Fulton jack we carry that's closest to your current one is The Fulton F2 #F1413230134. It has a static capacity of 2,000 pounds and 10 inches of lift height. It's a bolt-on jack that fits 4 and 5 inch trailer frames. I've linked a…

view full answer...

Answer 4

The Extreme Off-Road Swing-Up Jack w/ Dual Wheels - Sidewind - 1,100 lbs - Zinc #ORJW500D does not have a weld on option. It likely can be retrofitted to work with a bolt thru weld on bracket like the Jack Mounting Bracket for Fulton Marine Jack -…

view full answer...

Answer 5

The Xtreme Off-Road Swing-Up Jack w/ Dual Wheels #ORJW500D and #ORJW350D are pretty similar with the only differences being the weight capacity, 1,100 lbs vs 770 lbs, and the total travel, 18-3/8" vs 12". Aside from that the mounting…

view full answer...

Answer 6

With the ARK Xtreme Off-Road Swing-Up Jack #ORJW500D in its lowest position it is 6.49" from the center of the mounting point to the top of the jack. The other end of the jack when fully retracted is going to be 18.89" from the mounting…

view full answer...

Answer 7

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 8

Hey Steve, the schematic that shows the 645 mm measurement is for the #ORJW500D which is the Ark 500 Series Off-Road Jack. The answer that shows the 18" retracted length is referencing the #ORJW350D which is the 350 series jack and is smaller…

view full answer...

Answer 9

In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and this…

view full answer...

Answer 10

The Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR TruTurn 360-degree caster doesn't run on a bearing and the wheel only has a standard bolt. According to Fulton, the TruTurn only means that it is capable of rotating 360 degrees. For a swivel…

view full answer...

Answer 11

Hey Rod, The Ark Xtreme Off-Road Jack w/ 2 Wheels #ARK99FR has multiple slots in the outer tube of the jack that the mounting bracket can slot into. In the bottom slot you'd be right around 9-1/2" between the ground and frame with the wheels…

view full answer...

Answer 12

The bolt-on frame bracket for the Dutton-Lainson Square Swivel Jack part #DL22340 is welded to the outer tube so no, it cannot be adjusted. I think a better option would be the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR since the bolt-on…

view full answer...

Ground Clearance Using Fulton F2 Swivel Trailer Jack with Pivoting Footplate

Continue Researching