Will the 2nd Tier Kit For Malone MicroSport Trailers Also Fit on the Malone MicroSport Low Boy

Question

Question:

Would this fit the microsport low bed? If not, do you have the Microsport low bed 2nd tier kit?

asked by: Sako

0

Expert Reply:

Yes. The 2nd Tier Kit # MPG474 is also compatible with the Malone LowBed MicroSport Trailer - 78" Crossbars - 800 lbs # MPG464-LB.

expert reply by: Erik B

0

Answer 1

I checked to see if there was conversion kit to convert your Malone high bed trailer to a low bed #MPG464-LB. I know this isn't going to be ideal, but what you can do is reuse the U-bolts from the cross bars you have now, and reattach the cross…

view full answer...

Answer 2

You can use your Hobie carriers on your Malone MicroSport LowBed Trailer #MPG464-LB with the Malone Installation Hardware for Hobie Style Carriers #MPG5576-6. I have added a cut out of the instructions and linked them below but you just need to…

view full answer...

Answer 3

I checked with Malone and the Storage Trunk for Malone MicroSport and XtraLight Trailers #MPG481 is not a compatible accessory for the Malone MicroSport LowBed Trailer #MPG464-LB. As you mentioned, the Storage Trunk is compatible with other models,…

view full answer...

Answer 4

For a great option that allows you to transport a kayak up to 20 feet long, I recommend the Malone LowBed MicroSport Trailer - 78" Crossbars #MPG464-LB along with the Yakima BigCatch #Y04091. With the MicroSport trailer, it measures 13'…

view full answer...

Answer 5

You may be able to use the accessories you already use on your Thule Aero roof rack on the Malone LowBed MicroSport Trailer #MPG464-LB. You will need to verify if your accessories will fit on the 1-1/4" x 1-1/4" square bars on the trailer.…

view full answer...

Answer 6

We can piece together a Malone Lowbed trailer by first starting with the part #MPG464-LB and then a single bunk kit part #MPG561 and then the spare kit part #MPG465 and you'd be set. There isn't a kit with just the parts you are looking for…

view full answer...

Answer 7

The fenders on the Malone LowBed MicroSport Trailer #MPG464-LB are going to sit almost flush with crossbars. Do remember that the height of the Malone FoldAway-J Kayak Carrier #MAL98FR will give you over the top of the crossbars and the fact that the…

view full answer...

Answer 8

The Bunk Kit #MPG561 will fit and work perfectly on the Malone MicroSport LowBed Trailer #MPG464-LB that you referenced. We have recently confirmed with Malone.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Will the 2nd Tier Kit For Malone MicroSport Trailers Also Fit on the Malone MicroSport Low Boy

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching