Tools Needed To Install Fastway e2 Weight Distribution System

Question

Question:

What tools are required for installation of the e2 round bar WDH?

asked by: Dave

0

Expert Reply:

The only specialized tools aside from a basic socket set that will be required to install a Fastway e2 Weight Distribution System like part # FA94-00-1000 is a thin walled socket part # EQ70-00-4800 and torque wrench part # ALL644044.

expert reply by: Conner L

0

Answer 1

Unless you are worried about ground clearance I recommend you go with the round bar system. The Fastway e2 Weight Distribution w/ 2-Point Sway Control item #FA94-00-1061 is a round bar system that includes a 2" hitch ball. Round bar systems are…

view full answer...

Answer 2

In regards to the Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA94-00-0600 the hitch ball is sold separately and a requires 1-1/4" diameter shank. I recommend the 2-5/16" Hitch Ball #19286. It features a built-in wrench flats…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 9

Hey Ray, while there certainly is a lot of appeal to the Andersen WD systems like the part #AN88VR what we have found is that if the tongue weight is more than a few hundred lbs they just don't work as well as the traditional systems that use…

view full answer...

Answer 10

Hey, Joe. That's a great question. Backup cameras and rearview, observation, cameras are essentially the same, the difference comes down to how they’re wired. With a system like the Furrion Vision S+ Wireless RV Backup System #FR57AD, it’s…

view full answer...

Answer 11

Hi Jesse, The Fastway e2 Weight Distribution w/ Sway Control - Trunnion - 4,500 lbs GTW, 450 lbs TW #FA92-00-0450 will be a great option for your setup! The 5" rise shown in the photo is specifically for the system's head, but the overall…

view full answer...

Answer 12

Hello David, Thanks so much for reaching out! For your 2026 Ford F-350 diesel dually, you will want the EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" #EH54QR. This is the only front mount option we offer that is confirmed…

view full answer...

Tools Needed To Install Fastway e2 Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching