Dimensions of Torklift hitch # TLC1205-30

Question

Question:

What are the specs for the hitch. Hight width and center if bolt holes side to side. Thanks.

asked by: Kurt G

0

Expert Reply:

I checked with Torklift and they informed me that their hitch part # TLC1205-30 has the following dimensions:

The center to center hole is approx 39.5"
total width is about 41.5"
side plate height is 9.75"

expert reply by: Jameson C

0

Hitch Dimensions
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hey Rick, the part #e25ZV was not designed to be used with a trailer towing setup. Especially weight distribution as it adds quite a bit more strain on the setup. If you need more length from a weight distribution setup it's best to go with a…

view full answer...

Answer 9

Thanks for supporting a local business Christopher! So long as your 2012 Chevrolet Silverado is a 1500 and you need a class IV hitch, the Curt item #14301 is going to be the best option. It has a 2" receiver with a 10,000 lbs towing capacity and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Curt Trailer Hitch Receiver part #C15312 is what I recommend as a replacement for the factory trailer hitch on a 2002 Chevrolet Silverado 2500HD. In regards to the bolt hole spacing, this will be a different for the Curt Trailer Hitch Receiver as…

view full answer...

Answer 12

Thanks for the information Shane! To replace your VD0433 roof vents' interior trim, screen, and frame, you'll need the following parts: Replacement Screen Frame with Screen, Rocker Switch, and Wire for Ventline Roof Vents item #BVC0573-31R…

view full answer...

Dimensions of Torklift hitch # TLC1205-30

Product Page this Question was Asked From

Continue Researching