Replacement Hardware Kit For Curt Trailer Hitch Receiver 13167

Question

Question:

Seeking neu and bolt wire kit to reinstall my Curt 13167 hitch, Part #CURT 13167-BK

asked by: Paul E

0

Expert Reply:

For all of the replacement hardware and pull wires to reinstall your Curt trailer Hitch Receiver # C13167 on your 2020 Ford Transit Connect you will need the replacement hardware kit # RHK.

When on the product page of the # RHK you will select Curt from the drop down menu and then enter 13167 in the hitch item number box.

I included videos for both of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hey Tony, thanks for all of the details on you new truck! Based on that the correct Torklift tie down sets you'd need are the part #TL87DR for steel or part #TL85SV for the aluminum set. Do you need a set of turnbuckles too? What camper do you…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

The Kuat Transfer V2 Bike Rack for 2 Bikes part #KU74FR has an open center section design which will give you the best chance of visibility through a backup camera. That said, we aren't able to confirm compatibility as neither we nor the…

view full answer...

Answer 7

Many of the 4-pole trailer wiring kits we sell will install at the vehicle's tail lights. The harness connectors on such kits install in between the vehicle plugs and the tail lights themselves. For the 2014 Ford Transit Connect we have three…

view full answer...

Answer 8

I reached out to my tech contact at Curt and they have confirmed the fit of the wiring harness #C56218 for the 2018 Ford Transit Connect on the Titanium, XL, and XLT trim packages. Do you have a different trim package?

view full answer...

Answer 9

From my research, the backup camera of your 2017 Kia Sportage is centered above the license plate. The Kuat Transfer V2 #KU74FR will not block your camera while folded up. While I cannot confirm if the Kuat Transfer V2 #KU74FR will block your backup…

view full answer...

Answer 10

When installed on your 2018 Ford Transit Connect the Curt hitch part #C13167 is going to have about 10 inches of ground clearance. Since your vehicle sits so low to the ground it's hard to fit a hitch there and have decent ground clearance.

view full answer...

Answer 11

According to the owners manual for your 2016 Ford Transit Connect Titanium LWB you have a maximum towing capacity of 2,000lbs with or without trailer brakes. You will also need to ensure the added tongue weight does not cause your Transit to exceed…

view full answer...

Replacement Hardware Kit For Curt Trailer Hitch Receiver 13167

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching