Will Westin HDX Headache Rack Fit with Tonneau Cover

Question

Question:

Will this Rack work with a tonneau cover on a 2016 F350 or any other racks that will?

asked by: Timothy J

0

Expert Reply:

Since the Westin HDX Headache Rack # 57-8005 installs through the top of the bed rails it would allow a tonneau to fit between it as long as the tonneau cover attaches to the insides of the bed rails like the # TX569101, which fits your truck if it was a short bed.

expert reply by: Jameson C

0

Answer 1

Yes, due to how the BAKflip MX4 #BAK48330 you have on your 2022 Ford F-250 short bed installs the only ladder rack that's going to work is the Adarac Pro Series part #A4000952 which installs through the stake pockets and has vertical uprights…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 9

Welcome back Bill! For your 2020 Ford F-350 Dually, the Rock Tamers Adjustable Mud Flap System with Rock Screen item #RT77VR is going to be the correct one if you went with the upgraded 3" hitch receiver Ford offered and use 3" ball mounts.…

view full answer...

Answer 10

If you're wanting to install the Timbren #TFR350SDJ on your 2022 Ford F-350 then you'll want to measure the distance from where your factory bump stops are installed down to the point of contact on the axle. The Timbren #TFR350SDJ are…

view full answer...

Answer 11

Hi Jim! As long as your 2026 Alliance Valor 37V11 has the Lippert Rhino box currently, the B&W 5th Wheel to Gooseneck Pin Box - Lippert Rhino - 25K GTW - 3.25K TW #BW23RV will indeed fit. If you have a different pin box, just let me know and I…

view full answer...

Answer 12

We sure do Mike! To add a set of air bags and a compressor to your 4WD 2019 Ford F-350, I recommend the Firestone item #F44XV. This kit comes with a set of 5,000 lbs capacity air bags that will level out the rear end of your F-350 when you are towing…

view full answer...

Will Westin HDX Headache Rack Fit with Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching