Looking for Optronics MCL61AR26BK Trailer Fender Clearance/Marker Lamp

Question

Question:

I am looking for a optronics item MCL61AR26BK. Can you help me?

asked by: Roland

0

Expert Reply:

We do indeed have that particular fender clearance/marker light, we refer to it by our part number, which is # OPT36FR.

expert reply by: Mike L

0

Answer 1

The bolt hole pattern center on center for the Curt Trailer Hitch Receiver #13018 is 3-1/4 inches horizontally and 2-1/4 inch vertically. This varies from the 3-3/8 inch horizontal and 1-3/4 inch vertical measurements that a typical Pintle Hitch,…

view full answer...

Answer 2

The Curt Pintle Hook - Bolt On - 10,000 pounds #C48205 will work with The Curt Pintle Hook Mounting Plate for 2 inch Hitches - 6 inch Shank - 8 Hole - 17,000 pounds #C48343. It will not work with The B & W plate #BWPMHD14002 because it…

view full answer...

Answer 3

I had the bolt holes on the Super Titan Forged Pintle Hook Plate for 3" Trailer Hitches #RP38186 measured, and they are actually 5/8". That being said, I suggest going with the Curt Pintle Hook #C48215 to attach to it. This does include 1/2…

view full answer...

Answer 4

The standard size lunette ring is 3 inches like the Demco Lunette Ring - Adjustable Channel Mount - 3" Diameter - Black - 25,000 lbs #DM09557-81. The 2-1/2 inch rings will not fit in the adjustable channel mounts where the vast majority of the 3…

view full answer...

Answer 5

The Curt pintle hook part #C48210 has a 20k capacity and would mount up to the mount part #BWPMHD14002 that you referenced. This would be a great option that would work well.

view full answer...

Answer 6

I have a product that may work for you as we do not carry any torsion trailer axles like the one under your 10'X6' Aluma utility trailer. The Timbren Axle-Less Trailer Suspension System #A20RS545 is rated for 2,000lbs and will mount to the…

view full answer...

Answer 7

I have a complete replacement option for you, but just the lens portion of your light is not available by itself. Based on the model number on the rear of your light you will need the Optronics Thinline LED Trailer Fender Light - Submersible #OPT36FR…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Looking for Optronics MCL61AR26BK Trailer Fender Clearance/Marker Lamp

Product Page this Question was Asked From

Continue Researching