Replacement Trigger Latch for Old Fulton Trailer Coupler

Question

Question:

Will this repair kit work on an old Fulton trailer?

asked by: David D

1

Helpful Expert Reply:

The Coupler Repair Kit for 1-7/8" Curt Channel Couplers # C25094, will work with an old Fulton trailer coupler. You can see in the video that this traditional trigger style lock matches well with the photo you attached.

expert reply by: Jason S

1

click to enlarge

Answer 1

The Coupler Repair Kit part #C25194 is designed for Curt trailer couplers that use a 2" hitch ball. Since you have a Fulton trailer coupler I cannot recommend you use this kit. Instead, I recommend taking a look at part #F670801 which is for…

view full answer...

Answer 2

Fulton hasn't offered as 2 inch ball compatible A-Frame coupler in some years, so they no longer offer a repair kit. I'm sorry to say, I'd give a pretty good chance that the #CA-5100-RK would be a likely fit, but I couldn't guarantee…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 5

The channel of the Demco 21K #DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches to the second hole. The Titan #T4853100 dimensions are a little…

view full answer...

Answer 6

Hello, Phil! We do carry replacement wheel studs. The DeeMaxx drive-in wheel stud part #DE53GR would get pressed in from the back of the camper hub so that you can mount your rim to it. I've included a picture below showing all the dimensions of…

view full answer...

Answer 7

I might have an option for you but we don't offer any flush door latches with an extended striker. However, the Full Size Locking Steel Flush Door Latch part #L3980 matches your door cutout at 4-5/8" long x 3-3/8" so this is our best…

view full answer...

Answer 8

Hey Dianne! The Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2" Hitches item #ERT00108 weighs 35-1/2 lbs. What vehicle are you planning on using these on?

view full answer...

Answer 9

I spoke with the manufacturer and can confirm that the weight of Rapid Hitch Adjustable Aluminum Ball Mount #AM3411 is 17 lbs. This hitch is lightweight, yet very strong. It has a towing capacity of 7,500 lbs with 1-7/8" hitch ball, and 8,000…

view full answer...

Answer 10

Hi Tim, I was able to find the right replacement for your 32374 seal for your trailer, with the right replacement being the Grease Seal - Double Lip #21325.

view full answer...

Answer 11

You'll have to get me the bolt pattern and tire size that is stamped on the sidewall of what you currently have on your trailer for me to determine what the correct spare would be.

view full answer...

Answer 12

We actually have the Brake Buddy 32220 reverse solenoid available with the Titan Solenoid Valve Replacement Kit #TK71-755-00. The solenoid itself would be an exact replacement and it features the two mounting holes at the bottom like you described…

view full answer...

Replacement Trigger Latch for Old Fulton Trailer Coupler

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching