Low Profile A-Frame Trailer Tool Box

Question

Question:

I have a big Tex trailer 70 PI. Unfortunately it is tight between trailer and tongue jack. Ideally a low profile box around 12 inches. If it’s that short I can go about 18 inches deep. If the box is higher, I can only go about 12 inches deep. I would like it to be aluminum of medium strength. I can’t find what I am looking for. Any ideas?

asked by: Kevin W

0

Expert Reply:

We have a lower profile a-frame trailer tool boxes like with the UWS A-Frame Trailer Toolbox part # UWS04531 which is 13 inches tall. Front to back measure 16 inches and the width at front is 20 inches. The construction is aluminum like you are wanting as well.

I attached a dimensional drawing of the box for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your Big Tex 90PI trailer, I recommend checking out the: -RC Manufacturing T-Series Trailer Tongue Tool Box #350980. This toolbox has a cargo capacity of 2.6 cubic feet, measures 30" long x 14-1/2" tall x 14-1/2" wide, and is…

view full answer...

Answer 2

To verify that the 5 on 5" bolt pattern of the Provider ST205/75R15 Radial Trailer Tire w/ 15" Vesper White Mod Wheel #TA55RR matches your bolt pattern you're going to measure from the center of one bolt hole to the center of either of…

view full answer...

Answer 3

Hey Frank, on the etrailer box part #e64VV all of the walls are welded. The thickness of the steel is 13 gauge. What will you put in the box?

view full answer...

Answer 4

Good morning Sean, the etrailer Trailer Tongue Tool Box 3.4 Cu Ft #e64VV has the following inside dimensions: -17" inside height -13-3/4" inside depth (front to back) -33-1/2" inside width on back side and 15-3/4" width on front…

view full answer...

Answer 5

Good afternoon, Keethe; that's a very good question! In regard to the etrailer Trailer Tongue Tool Box 3.4 Cu Ft #e64VV, I'd say it has similar build quality and features when compared to other options such as RC Manufacturing T-Series…

view full answer...

Answer 6

Hello Stevin, great question. Luckily when our warehouse gets the etrailer Trailer Tongue Tool Box 3.4 Cu Ft #e64VV or etrailer Trailer Tongue Tool Box 6 Cu Ft #e44VV ready for shipment, they are placing it in a double-wall thick box along with…

view full answer...

Answer 7

Not sure without knowing how big your trailer's tongue is. Maybe you can move your battery back some. The etrailer Trailer Tool Box item #e64VV measures 34" long x 18" tall x 14-1/4" wide. I have attached a diagram below so you can…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Low Profile A-Frame Trailer Tool Box

Product Page this Question was Asked From

Continue Researching