Will Curt Class III 2-Inch Hitch # C13105 Fit a 2008 Toyota Sienna Limited

Question

Question:

Is there a DVD for the 2008 model?

asked by: Jerry C

0

Expert Reply:

The Curt Class III 2-Inch Hitch, part # C13105, you have referenced, will fit your 2008 Toyota Sienna Limited.

If you are meaning an installation DVD on the hitch, I do not offer any installation DVDs. I am including a link to the installation instructions and a link to an installation video of the Curt hitch being installed on a 2006 Sienna. The vehicle is a different year, but it is the same design second generation Sienna as you 2008 model.

If you plan on doing some towing, I recommend the etrailer ball mount kit, part # EBMK4. It comes with a ball mount, interchangeable ball set, hitch pin and clip, and a carrying bag. For trailer wiring use Tow Ready T-One Wiring Harness, part # 118304. I have included links to the instructions and an install video for the wiring as well.

expert reply by: Jeff D

0

Pedro

11/9/2021

Hi. I'm looking for a hitch like this but one that is concealed for a 2008 Toyota Siena Le. Do you guys sell any?

Les D.

11/12/2021

I added a link below to all of our hitches that exactly fit your Sienna. There is a link at the top of the page for a Video comparison. Since one is no more hidden than the others, and since the Draw-Tite is better in other areas, I would recommend the Draw-Tite # 75237 Class-3 hitch with 2" receiver. There are other Class-2 hitches (with 1-1/4" receivers) for a little less money, but there are many more hitch accessories for 2" receivers and I prefer the beefier construction of a Class-3. Regardless of the hitches individual ratings, the Sienna is limited to 350 pounds tongue weight and 3500 pounds of towing capacity.

Helpful Links

hitch-2008_toyota_sienna.htm

Answer 1

This is a great question and I can definitely understand being a bit overwhelmed trying to work through all the available hitch options for your vehicle. Just to cut right to it I specifically recommend the Curt Class III Trailer Hitch #C13343 for…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

While we cannot confirm for sure what the "L" means on the 11033L, the "L" does not make a differences when coming to fitment of the hub. With that being said, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern…

view full answer...

Answer 10

Hey Craig, thanks for reaching out! I believe the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK will work as replacements for your 2008 Featherlite 4926 trailer, but you'll need to confirm this on your end. These lights carry the…

view full answer...

Will Curt Class III 2-Inch Hitch # C13105 Fit a 2008 Toyota Sienna Limited

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching