Replacement for MaxxAir MaxxFan Circuit Board 10-04751KS

Question

Question:

What is the replacement part for max air part# 10-04751ks circuit board? It has 4 speeds and open/close vent functions+ rain sensor. Also I tore wires out of rain sensor. Will the fan work without sensor plugged in? Thanks

asked by: Jon P

0

Expert Reply:

The correct replacement for your MaxxAir Circuit Board 10-04751ks is the following part:

- Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS

As for the sensor wires, so long other wires are not damaged, I don't see any reason why the fan won't operate, just without the rain sensor, of course.

expert reply by: Kyle S

0

click to enlarge

Answer 1

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Answer 2

You can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS to replace your damaged 10A04751ksz MaxxAir circuit board. This is a direct replacement.

view full answer...

Answer 3

For a replacement circuit board you can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS. We have confirmed with MaxxAir that this is the correct for what you have.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement for MaxxAir MaxxFan Circuit Board 10-04751KS

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching