Replacement for MaxxAir Circuit Board 10A04751KS

Question

Question:

What is the direct replacement for 10A04751ksz circuit board.maxxair fan

asked by: Rex B

0

Expert Reply:

You can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS to replace your damaged 10A04751ksz MaxxAir circuit board. This is a direct replacement.

expert reply by: Erik B

0

Answer 1

The Replacement Printed Circuit Board #MA10A04751KS is the correct part for your MaxxAir 4951KS roof vent.

view full answer...

Answer 2

Everything I could find on the switch for a Dometic 9100 Power Awning is that the correct switch is the 3310455.062. While we do not carry that exact switch, it is a 4 wire design. This means you can use the Replacement Switch Kit #LC285500. Because…

view full answer...

Answer 3

The correct replacement for your MaxxAir Circuit Board 10-04751ks is the following part: - Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS As for the sensor wires, so long other wires are not damaged, I don't…

view full answer...

Answer 4

You will need to test the wiring to determine if the Lift Motor #MA10-20270 is getting power when you press the remote. This will help you determine if the motor is bad or the Printed Circuit Board #MA10A04751KS on your MaxxAir fan. A Test Light…

view full answer...

Answer 5

After replacing The Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS, and the motor still does not open the lid you will need to replace the motor. The Replacement 12-Volt Variable Speed Fan Motor for MaxxAir MaxxFan RV Roof…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement for MaxxAir Circuit Board 10A04751KS

Continue Researching