Replacement Foot Pad for Lippert Stabilizer Jack 337199

Question

Question:

LC314667 will these fit 2019 XLR 5th wheel with LCI Power Stabilizer Jack - model #337199 on the rear?

asked by: Dale L

0

Expert Reply:

We have the correct replacement foot pads for your Lippert Stabilizer Jack 337199, but the ones you mentioned will not work with that stabilizer.

Instead, the correct part is the Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks # LC157584.

expert reply by: Kyle S

0

Answer 1

The SnapPad XTRA Square #SN99FR is the correct set of snap pads to fit the 6" Foot #LC157584 on the Lippert High-Speed Power Stabilizer Jack. This kit includes 4 pads or you can get them Individually #SN77FR if you only need one set or one get…

view full answer...

Answer 2

It can indeed be used if the jack leg can accommodate the 1-1/4 inch width beetween the mount ears as shown in the provided photo. If the leg is too wide to fit in between the ears, they might fit inside the leg is the inside of the leg is greater…

view full answer...

Answer 3

The Electric Stabilizer Jack Support Arm #LC1134122 and Foot Assembly #LC157584 are the only replaceable parts for the legs on your Lippert PSX1 Stabilizer Assembly #LC298707. If you bent the leg itself you will need to replace the entire assembly.

view full answer...

Answer 4

Since the leg of your Lippert Stabilizer jack setup part #LC298707 aren't replaceable you would need to replace the entire unit unfortunately.

view full answer...

Answer 5

Most likely one of the leg components is bent and is being prevented from moving because of that. You might be able to get lucky and you'll be able to bend it back if its not too bad but otherwise you'd have to replace it with it another…

view full answer...

Answer 6

Hi Charles, The screws you have in the picture are the ones needed if you were mounting the camera #FOS07TASF into an already mounted shark fin camera mount. If you don't have a prepped trailer with the mounts already in place then you'll…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Foot Pad for Lippert Stabilizer Jack 337199

Product Page this Question was Asked From

Continue Researching