Using Larger Foot Plate on Lippert Stabilizer Jacks
Updated 09/11/2020 | Published 09/09/2020
Products Featured in This Question
Question:
Can this larger pad be used on Lipperts Power Stabilizer jacks for a travel trailer? I believe your standard replacement part for the foot/pad is Item # LC157584
asked by: Ray A
0
Expert Reply:
It can indeed be used if the jack leg can accommodate the 1-1/4 inch width beetween the mount ears as shown in the provided photo. If the leg is too wide to fit in between the ears, they might fit inside the leg is the inside of the leg is greater than 1-3/4 inches.
expert reply by:
Mike L
0
click to enlarge
Product Page this Question was Asked From
Ultra-Fab Footplate for Landing Gear and Stabilizer Jacks - 8" x 5-3/4"
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Ultra-Fab Products
more information >
Continue Researching
- Search Results: car tie down straps
- Search Results: roof vent covers
- Shop: Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks - Qty 1
- Search Results: lugnuts
- Video: Review of Ultra-Fab Products Footplate for Landing Gear and Stabilizer Jacks - UF17-940006
- Shop: Lionshead Steel Modular Trailer Wheel - 16" x 6" - 8 on 6-1/2 - Silver
- Search Results: stabilizer foot
- Video: Feature Breakdown: Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks
- Shop: Erickson E-Chock Wheel Chock for E Track - Powder Coated Steel - Qty 1
- Shop: Erickson E Track Tie-Down Kit w/ 4 Ratchet Straps with Roller Idlers and 2 Wheel Chocks - 1,100 lbs
- Shop: Erickson E Track Strap with Ratchet - 2" Wide x 16' Long - 1,165 lbs
- Shop: etrailer Axle Strap w/ D-Rings - 2" Wide x 36" Long - 3,333 lbs - Qty 1
- Shop: Ultra-Fab Footplate for Landing Gear and Stabilizer Jacks - 8" x 5-3/4"
- Q&A: Availability of Raised Gooseneck Ball for 2024 GMC With OEM Prep Package
- Video: A Closer Look at the Curt Multi-Fit Ball Kit w/ 4" Offset for Factory Gooseneck Hitches
- Shop: Gooseneck Hitch
- Q&A: Will a Wheel With Bolt Pattern 8 on 170MM Fit on the Dexter Hub/Drum # 8-219-4UC3-EZ?
- Q&A: Is There a Trailer Wheel Available with Bolt Pattern of 8 on 170 mm?
- Video: Review of the Replacement Footpad and Pin for Stromberg Carlson Landing Gear
- Search Results: level
- Search Results: magnadyne
- Search Results: psx1
- Q&A: Can You Use Larger Footpads For Lippert Stabilizers
- Video: Review of the Footplate for 2,000-lb and 5,000-lb Round, A-Frame Jacks
- Video: What to Know About the Dexstar Steel Mod Trailer Wheel- 16" x 6" Rim
- Q&A: What is Difference Between Lippert # PSX1 and PSX2 Stabilizer Jacks
- Q&A: Troubleshooting A Lippert PSX1 Stabilizer Jack That Does Not Extend But Retracts
- Video: Review of the Double Spacer Kit for Lippert Power Stabilizer Jack
- Q&A: Replacement 16 x 6 Inch Wheel for a Big Tex 14GN Trailer