Can Bent Leg On Lippert High-Speed Power Stabilizer Jack Be Replaced

Question

Question:

PSx1 can you buy the unit without the electrical parts. I have a bent leg everything else is fine.

asked by: Terry M

0

Expert Reply:

In regards to the Lippert High-Speed Power Stabilizer Jack part # LC369774, you can replace the support arms with part # LC1134122 and the foot assembly with part # LC157584. The legs themselves are not repairable, if either are bent then the entire unit would need to be replaced.

expert reply by: Conner L

0

Answer 1

It can indeed be used if the jack leg can accommodate the 1-1/4 inch width beetween the mount ears as shown in the provided photo. If the leg is too wide to fit in between the ears, they might fit inside the leg is the inside of the leg is greater…

view full answer...

Answer 2

We have the correct replacement foot pads for your Lippert Stabilizer Jack 337199, but the ones you mentioned will not work with that stabilizer. Instead, the correct part is the Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks…

view full answer...

Answer 3

Since the leg of your Lippert Stabilizer jack setup part #LC298707 aren't replaceable you would need to replace the entire unit unfortunately.

view full answer...

Answer 4

The Electric Stabilizer Jack Support Arm #LC1134122 and Foot Assembly #LC157584 are the only replaceable parts for the legs on your Lippert PSX1 Stabilizer Assembly #LC298707. If you bent the leg itself you will need to replace the entire assembly.

view full answer...

Answer 5

Most likely one of the leg components is bent and is being prevented from moving because of that. You might be able to get lucky and you'll be able to bend it back if its not too bad but otherwise you'd have to replace it with it another…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Can Bent Leg On Lippert High-Speed Power Stabilizer Jack Be Replaced

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching