Availability of Replacement Fuse for Jensen TV Power Cord Adapter

Question

Question:

I need the fuse thats in the inside of the DCCIG09 TV Adapter Cord. The part number is F8AL Fuse. Also is it a 250V. I dont know what that means but it shows that 250V when I look up the F8AL F8AL250V

asked by: Kathy

0

Expert Reply:

I'm not sure what fuse is inside the Power Adapter Cord # DCCIG09 as Jensen doesn't have it available as a replacement part. The only solution we have would be for you to replace the whole thing.

expert reply by: Jon G

0

Answer 1

The quick disconnect outlet on your Rockwood is already regulated so you need new hose that doesn't have a regulator on it. The hose needs a quick disconnect on one end of course and a 3/8 female flare on the other. We carry two hoses with these…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 10

Hey Robert, thanks for reaching out. The Curt Cold Weather 7-Way RV Style Connector #C23RJ uses a combination of 14-gauge and 10-gauge wire. The black 12V power wire and white ground wire are 10 gauge, while the brown, red, blue, green, and yellow…

view full answer...

Answer 11

Hey Gary, thanks for reaching out. No, nothing is missing from the #C96GJ kit. Curt uses the term “T-Connector” pretty broadly for a lot of their plug-and-play harnesses, even when they are not a true tee-style splitter like you were expecting. On…

view full answer...

Answer 12

Hey Mark, thanks for reaching out, and good question. That “16/18 gauge” wording throws a lot of people off. The TowSmart 16 to 18 Gauge, 4 Conductor Wire #TS57QR isn’t all one size. It’s a 4-conductor cable with mixed gauges inside, two wires are 16…

view full answer...

Availability of Replacement Fuse for Jensen TV Power Cord Adapter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching