Are There Replacement Parts Available for the Motor in the Lippert Electric Tongue Jack 285318

Question

Question:

I have a Lippert 285318 3500LB Power Tongue Jack Black there is a spring broken in it and the motor will not turn, I hate to buy and entire jack for a spring on the brush, I was wanting to just get two new springs and install them myself if that is possible to get them. Please let me know what you can do, or direct me to who can help, I didnt know if you made the motor or if someone else did. Regards

asked by: Gloria

0

Expert Reply:

I have a solution for you, but the springs you're referring to and even the motor itself are not replaceable in the Lippert Electric Tongue Jack # LC285318. For this reason you would need to replace the jack itself, but that jack is still available for purchase so you can use the same jack that you've currently got on your trailer if you'd like.

expert reply by: Erik B

0

Answer 1

We do not have a way to get just the replacement motor for the Lippert jack you have so you'd have to replace it with a new one like the part #LC285318.

view full answer...

Answer 2

I checked and found the manual for the Lippert Electric Trailer Jack #LC285318 and there was no mention of anything going in the hole beforehand to tighten them. I added a cut out of the manual for you which shows the parts for this jack, and it does…

view full answer...

Answer 3

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 4

For a Ram 3,500 lb jack we have the replacement Light Switch #EJ-3520-LSW and Power Switch #EJ-3520-PSW. If you remove the cover you should be able to then pop the switches out of the head to replace them. There should also be the blade-style wiring…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Are There Replacement Parts Available for the Motor in the Lippert Electric Tongue Jack 285318

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching