Pop n Lock for my ARE Camper Shell

Question

Question:

I have a ARE Z series camper shell what electric camper shell lock would I need

asked by: Ed S

0

Expert Reply:

For your ARE camper shell, if it has frameless bonded glass I recommend the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers # PAL9555 or # PAL9772.

expert reply by: Randy B

0

Answer 1

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you have on your Tacoma. You can wire it so that the key FOB of your Tacoma will unlock it as well.

view full answer...

Answer 2

As long as your vehicle has power door locks and your ARE V-Series truck cap has a frame-less, bonded glass door with a 1-1/8" center hole for a rotary latch you can use the Pop & Lock Power Locking Handle, part #PAL9555. There are a few…

view full answer...

Answer 3

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with the keyless…

view full answer...

Answer 4

Hi Lee; can you tell me which end cap it is based on the picture below? There are four possible options. Since you mentioned the foam I'm guessing it is either the Side Rail End Plug_RH Foam Seal or Side Rail End Plug_LH Foam Seal. The end caps…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Pop n Lock for my ARE Camper Shell

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching