Recommended 8" x 6.5" Wheels for Zero Turn Lawn Mower

Question

Question:

I need an 8” rim for my 0 turn mower it is 6.5”wide and has 4 lug holes X 4” on center! It fits a 18 X 6.5 - 8.0 nhs turf tire. Can you help me?

asked by: Max S

0

Expert Reply:

The Steel Trailer Wheel part # AM20021 is the best option we have for you and it works great for most lawn mowers. It measures 8" diameter x 7" wide so it will be a bit wider than the one you have now but that actually should not be too much an issue if you replace both. These will work just fine with 18x6.5 tires.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Hey Rick, the part #e25ZV was not designed to be used with a trailer towing setup. Especially weight distribution as it adds quite a bit more strain on the setup. If you need more length from a weight distribution setup it's best to go with a…

view full answer...

Answer 7

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 8

Thanks for supporting a local business Christopher! So long as your 2012 Chevrolet Silverado is a 1500 and you need a class IV hitch, the Curt item #14301 is going to be the best option. It has a 2" receiver with a 10,000 lbs towing capacity and…

view full answer...

Answer 9

The difference between the Curt #14211 and the Curt #C14008 is pretty subtle, but it has to do with how they mount to the frame of the vehicle. The Curt #14211 mounts in factory drilled holes further forward in the frame allowing it to fit on a 2003…

view full answer...

Answer 10

The Curt Trailer Hitch Receiver part #C15312 is what I recommend as a replacement for the factory trailer hitch on a 2002 Chevrolet Silverado 2500HD. In regards to the bolt hole spacing, this will be a different for the Curt Trailer Hitch Receiver as…

view full answer...

Answer 11

Hey Chris, I attached a picture of the B and W hitch part #BWHDRH25182 installed on a truck with the stock spare which is 2 inches shorter in diameter than the size 285/70-17 that you mentioned. There is definitely clearance from side to side for it…

view full answer...

Recommended 8" x 6.5" Wheels for Zero Turn Lawn Mower

Product Page this Question was Asked From

Continue Researching