Repair Kit for Fulton A-Frame Coupler with Trigger Latch

Question

Question:

will your ca-5100-rk kit work on my 5000lb fulton a-frame hitch the picture looks the same as mine

asked by: Neal

0

Expert Reply:

We have a Fulton coupler repair kit with the part # F670801 that you'd want instead of the # CA-5100-RK which only fits the Ram brand of couplers.

expert reply by: Jameson C

0

Answer 1

Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler #CA5100B, which has a trigger latch and has a black paint finish. The same coupler is available with a…

view full answer...

Answer 2

The Repair Kit for etrailer and Ram A-Frame Couplers #CA-5100-RK only fits the following couplers #CA5100B, CA-5100-BLB, and #CA-5100-Z, so it would not solve your connection difficulty, unless you had one of these specific couplers. Aside from…

view full answer...

Answer 3

Coupler Repair Kit #CA-5100-RK includes all parts needed to rebuild an etrailer brand or Ram brand 5K-rated 2-inch ball coupler with a trigger latch. It consists of all components other than the housing. If you have one of these models - #CA5100B,…

view full answer...

Answer 4

Yes there is a difference between couplers for an a-frame trailer and a straight tongue trailer. They are a very different design so if you have an a-frame trailer you'd need something like the #CA-5210-B which you can see matches the shape of…

view full answer...

Answer 5

I do have an option for you but the trailer coupler repair kits are model specific so in order to obtain the correct one you will need to know what exact model you have. That said, the sticker with this information can wear off which it sounds like…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Repair Kit for Fulton A-Frame Coupler with Trigger Latch

Product Page this Question was Asked From

Continue Researching