Brake Controller Plug and Play Adapter Cord For Tekonsha Primus IQ in 2017 Nissan Frontier

Question

Question:

Hi I have the Tekonsha Primus IQ brake controller could someone tell me what wiring harness I need to go from the controller to the factory plug in on my 2017 Nissan Frontier sv 4x4. Thank You

asked by: Glen W

0

Expert Reply:

To use the Tekonsha Primus IQ part # TK90160 in the 2017 Nissan Frontier you will need adapter part # 3050-P which will plug into the factory port. I have attached an installation video for your reference on a 2016 Nissan Frontier but it will be the same for your 2017.

expert reply by: Heather A

0

Answer 1

We have not had the opportunity to do a brake controller installation on a 2023 Nissan Frontier yet. But if the plug is located in the same place as the 2022 model year, then the plug will be tucked behind the kick plate located to the left of the…

view full answer...

Answer 2

If you're speaking about how to remove the kick panel on a Nissan truck to install a wiring harness like #118266, the linked video shows how the kick plate is removed. If you're speaking of the blue relay that is included in the Curt Relya…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Brake Controller Plug and Play Adapter Cord For Tekonsha Primus IQ in 2017 Nissan Frontier

Continue Researching