What is Depth Including Water Valves of D&W Inc. Spray-Away RV Exterior Hose Hookup w/ Shower Valve

Question

Question:

I would like to intall this item on the transom of my boat but there is limited depth distance. Your specs say the depth is 3-1/2inch deep. Does this length include th 1-1/2inch shank inlet? I need to know the exact length of the depth of thee box to include the shank inlet to back of the face surface. see picture. Thanks

asked by: Dino A

0

Expert Reply:

The recommended depth needed when installing the Exterior Hose System part # PF247201 is 6 inches. The water lines at 1-1/2 inches of depth to the housing which is 3-1/2 inches deep.

expert reply by: Jameson C

0

Answer 1

Yes John, the Quick Connect Garden Hose Adapter for Spray-Away part #PF247007 is compatible with the Spray-Away RV Exterior Hose Hookup w/ Shower Valve part #PF247201. This adapter will allow you to hook up a garden hose to the quick disconnect valve…

view full answer...

Answer 2

We have some parts that are used to make an outdoor shower that would work for you. You'll need to source a fitting from your local hardware store that will connect the supply lines of your faucet to have a single input. I have listed the parts…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...