Replacement Trailer Brake Assemblies for Part Number # 023-105-00

Question

Question:

I have a 023-105-00 break , which product do you have that will interchange with that? Thanks

asked by: Jody F

0

Expert Reply:

We have the exact brake assembly you are looking for with the part # 23-105 which is a left hand 6,000 lb Dexter brake assembly. The matching right hand side then is the part # 23-106. It's always smart to replace them in pairs if you can so that both sides will have equal braking performance.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Electric brakes have 2 wires located at the back. One is for power and the other is for ground (it doesn't matter which is used for which function). The ground wires should be connected to the trailer frame. The only other place that would carry…

view full answer...

Answer 2

Hey David! The DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers item #DE46AR will work so long as you have idler hubs with a 8 on 6-1/2 lug nut pattern like item #DE46VR. These are slip on rotors so you're definitely going to need some…

view full answer...

Answer 3

There are hubs/drums available for the #23-105 and #23-106 brake assemblies. You'll want to go with a 12 x 2 drum, and you'll want to choose one that has bearing compatible with your existing spindle and a lug and bolt circle pattern…

view full answer...

Answer 4

I would check the magnets for wear before going on to test them with a meter. If the magnets show abnormal wear or if you can see the windings beginning to show through the friction surface of the magnet then they will need to be replaced. To further…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement Trailer Brake Assemblies for Part Number # 023-105-00

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching