Glo Brite 118A/117R LED Bulb Replacement

Question

Question:

Do you have a replacement LED instead bulbs red and amber

asked by: Gary Q

0

Expert Reply:

The bulb type of the Glo Brite 118A/117R you have is a 194 so for an LED you'd just want the # DI88VR.

expert reply by: Jameson C

0

Answer 1

The correct replacements we offer for the Glo Brite Marker Lights 118A and 117R is the Trailer Clearance or Side Marker Light part #MC44AB for amber and part #MC44RB for red.

view full answer...

Answer 2

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 3

We don't carry lights with those colors, so you will need to test them based on function. Normally black and red are power and white is ground like you see in the #STL69RB. I would try the yellow as ground. Red is most likely the turn signal and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Glo Brite 118A/117R LED Bulb Replacement

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching