Brake Controller Wiring Harness for 2020 Toyota Tacoma

Question

Question:

I need to know which harness to purchase to connect a Prodigy P3 to a 2020 Toyota Tacoma TRD Pro. I believe it is part # 3031-P

asked by: James M

0

Expert Reply:

You are correct, the right brake controller harness for the 2020 Toyota Tacoma is indeed the # 3031-P. The harness plugs into the white connector located behind the driver's side kick panel. I've provided a photo showing where the connector is located.

expert reply by: Mike L

0

click to enlarge

Answer 1

Hey Robert, For your 2020 Tacoma I recommend the etrailer hitch #e98905. This is a simple bolt on installation hitch and features a capacity of 6000lbs for towing. Plenty for the trailer you are wanting to pull. Along with the hitch you are also…

view full answer...

Answer 2

Thanks for the additional information! For your 2021 Geo Pro 19FBS trailer, I recommend the Adjustable Width Trailer Hitch Receiver for RVs item #13703. This universal hitch fits trailer frames that are 22" to 72" wide so this will be…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Brake Controller Wiring Harness for 2020 Toyota Tacoma

Featured Help Information

Miscellaneous Media

Continue Researching