What is Part Number for Replacement Westin Step Bar Hardware for 2003 GMC Sierra 1500 Extended Cab

Question

Question:

part # mounts with cab bolts 2003 gmc extended cab1500 3 in platnium series step bars hardware

asked by: Larry W

0

Expert Reply:

The correct hardware kit for the Westin Platinum Nerf bars that fit your 2003 GMC Sierra 1500 with an extended cab is the part # 23-168PK you referenced as the correct step part number is # 23-1680. This comes with all new bolts and hardware to install the bars.

expert reply by: Jameson C

0

Answer 1

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 2

There are multiple ground locations on your 2003 Chevy Silverado 4x4. I don't believe that is your issue since you have the factory wiring harness. I recommend you use a circuit tester like #PTW2993 and test the pin functions of your trailer…

view full answer...

Answer 3

I'm pretty sure that's to wire up a third brake light on a camper shell. To know for sure, take a circuit tester, like our part #PTW2993, and test that wire while applying the truck's brakes. If I'm correct it's a dedicated brake…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What is Part Number for Replacement Westin Step Bar Hardware for 2003 GMC Sierra 1500 Extended Cab

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching