Recommended Trailer Hitch And Wiring For 2020 Toyota RAV4 Hybrid

Question

Question:

We purchased our 2020 RAV4 Hybrid without the tow package and now wondering what we need now that we're looking to puchase a jet ski with trailer?

asked by: Kerry G

0

Expert Reply:

To pull your jet ski trailer you will need a trailer hitch, wiring harness, ball mount, and tow ball. It is important to check your vehicle owners manual as well just to make sure you don't exceed the RAV4's capacity before you purchase your tow setup.

The Curt Trailer Hitch Receiver # C13416 is a great choice of hitch that is a confirmed fit for your 2020 Toyota RAV4. It has an attractive gloss black finish and the 2" receiver allows for a variety of accessories to be carried. The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56434 is a great choice of wiring that sets you up for a 4-way trailer connector. Finally an adjustable ball mount will allow you to add rise or drop as needed to level your tow setup. I recommend the Curt Channel Style Adjustable Ball Mount # C45900 as a simple solution. For more about determining rise or drop, the included Help Article is a great resource.

Included are some helpful video resources to get you started!

expert reply by: Patrick R

0

Larry D.

7/8/2020

We have a 2020 RAV4-HYBRID and want to pull a Yakima Rackandroll canoe and bike trailer with a maximum cargo weight of 350 lbs. Is this the appropriate hitch, ball, and connector for our situation? Thank you.

Chris R.

7/13/2020

Yep! All the parts Patrick mentioned above will work perfectly on your RAV4 Hybrid so that it can pull the Yakima Rack-and-Roll trailer.

Joe B.

9/6/2020

I had the dealer install a 2 inch tow receiver when I bought my 2020 RAV 4 hybrid with the intent of putting a lift and scooter on the back because I have mobility issues. The company I was going to buy the lift and scooter from say the tongue weight will not support more than 125 pounds. Is the weight limitation correct?

Jon G.

9/8/2020

That company is telling you how much your RAV4 can handle? Or they are saying that their lift will only be able to support up to 125 lbs? Typically if you have a 2" hitch receiver it will be at least a Class III and at least have a tongue weight of 350 lbs. You can verify this by looking at the sticker on your trailer hitch itself and then comparing that to the max tongue weight rating of your RAV4 that's listed in your owner's manual. Whichever one is lower will be your limiting factor and your max tongue weight rating.

Chris

4/5/2024

I'm looking to get a tear drop trailer for my 202 Rav4 hybrid, It cam with the hitch but doesn't have the wiring harness. I've been look around and they are all 4 pin and most of the trailers are 7 pin, is there an easy way to turn the 4 into a 7 pin and add in a cordless brake remote?

Jerred H.

5/8/2024

@Chris The only way to add a 7-Way to your RAV4 hybrid is to use the Universal Installation Kit for Trailer Brake Controller item # ETBC7. I wouldn't necessarily say it's easy but there are no plug and play options.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Recommended Trailer Hitch And Wiring For 2020 Toyota RAV4 Hybrid

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching