Dimensions Of Camco Olympian Wave 3 Catalytic Safety Heater part # CAM57331

Question

Question:

What are the dimensions of the boxy portion of this unit not including the buttons, knobs, fuel inlet, etc.?

asked by: Heather

0

Expert Reply:

I went out to the warehouse to measure Camco Olympian Wave 3 Catalytic Safety Heater part # CAM57331 and the unit no longer has the knobs and buttons on the front. The black knob is on the left side of the unit and the red switch is on the left side of the unit pictured in the photo I have attached. I have added some dimensions for you.

expert reply by: Heather A

0

click to enlarge

Answer 1

In regards to the Camco Olympian Wave 3 Catalytic Safety Heaters like part #CAM57331, Camco states that the space in which the heater is used must have sufficient airflow to allow for a complete burn of the gasses. In the owner's manual for the…

view full answer...

Answer 2

Yes, the Camco Low-Pressure LP Gas Regulator with Hose #CAM57703 will work with your 30,000-BTU heater. This 6-foot hose and low-pressure regulator is rated for up to 75,000-BTU applications. This part can be used with a heater such as the Camco…

view full answer...

Answer 3

The square connectors you are looking for on your 2008 Dodge Ram to install the #C56071 are on the harness that runs to the 7-way of your truck. Easiest way to find it is to trace the harness from the back of the 7-way to the front of the truck.…

view full answer...

Answer 4

Due to the age of the truck, neither Curt nor Tow Ready have a listing for the vehicle, but there are only two possibilities. The wiring harness that plugs into the rear of your OEM 7-way should have either a rectangular or a round connector on it.…

view full answer...

Answer 5

You do not want to use the ASA to replace your duo therm. You're going to want to replace it with a Dometic unit #DMC33ZR instead.

view full answer...

Answer 6

Hi Alex; the gauge on the Big Truck Big RV Tongue Weight Scale for Trailers #BTBRV004 has a +/- 5% full scale accuracy and displays weight in 20-lb increments up to 1,000 lbs. We also have it available with a SnapPad #BTBRV99FR. If you want something…

view full answer...

Answer 7

The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit #BWGNRK1400 measures 34" long X 8" wide. However, this is designed to fit the 1973-1987 Chevy/GMC C/K Series Pickup. For your FL70 Freightliner the Buyers…

view full answer...

Answer 8

You will not want to install a heater like the RV Holding Tank Heater #372HTH-A between the metal straps supporting it and the tank as it can't be in contact with a conductive surface. This heater is 30" long x 13" wide but there are…

view full answer...

Answer 9

Yes, the RV Holding Tank Heater #372HTH-A that you referenced does have an adhesive backing

view full answer...

Answer 10

Hey George, we do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings #L68149…

view full answer...

Answer 11

It sounds like you have the B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3770 in your 2016 Chevrolet Silverado with 6-1/2' bed and prep package. For the other Chevrolet that has the B&W turnover ball…

view full answer...

Answer 12

The Camco Olympian Wave 3 Catalytic Safety Heater for Small RVs #CAM57331 can heat a larger area (120 square feet) compared to the Little Buddy Heater which claims 95 square feet, has a built in automatic Piezo-electric spark starter which will last…

view full answer...

Dimensions Of Camco Olympian Wave 3 Catalytic Safety Heater part # CAM57331

Product Page this Question was Asked From

Continue Researching