Do the Races Come Fully Seated in the Trailer Hub and Drum Assembly # 84656uc3
Updated 03/29/2012 | Published 03/28/2012 >
Question:
I just purchased 4 hubs as noted above and found that the outer races were seated all the way. The inner races appeared not to be seated all the way they were flush with the first lip. Theres a gap in-between the race and the inner hub. Are the races fully seated on the inner side? Or do I need to drive the inner races until theres no gap ? Thanks.
asked by: Beau W
Expert Reply:
I went out to the warehouse and checked our stock of hub and drum # 84656uc3. All of the units are just as you have described and the races are installed correctly. If you are looking at the inner race from the back side of the hub and drum, there will be a small space of smooth metal towards the center of the hub and then a rough patch right in the middle. Take a look at the pictures I have included.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 6 on 5-1/2
- Trailer Hubs and Drums
- Hub with Drum
- Standard
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: 8~201~9
- Search Results: trailer brakes
- Search Results: trailer jack
- Search Results: gromet
- Search Results: trailer lights
- Search Results: marker lights
- Search Results: trailer brake drum
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Hub with Integrated Drum - AKHD-655-35-K
- Video: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles: The Breakdown
- Video: Detailed Breakdown of the Thinline LED Clearance and Side Marker Light
- Video: Peterson Clearance and Side Marker Trailer Light Spec Review
- Video: Right Angle 2-Wire Pigtail for Optronics Trailer Lights Feature Review
- Shop: Dexter Trailer Hub and Drum Assembly - 5,200-lb E-Z Lube Axles - 12" - 6 on 5-1/2
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 6 on 5-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 6,000 lb E-Z Lube Axles - 12" - 6 on 5-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 6 on 5-1/2 - Pre Greased
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 6 on 5-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly - 7K E-Z Lube Axle - 8 on 6-1/2 - Pre-Greased - 1/2" Stud
- Video: Review of etrailer Trailer Hubs and Drums - Galvanized Idler Hub - AKIHUB-440-2-G-1K
- Video: All You Need to Know About the Kenda 4.80-12 Bias Trailer Tire with 12" White Wheel
- Shop: Trailer Wiring
- Shop: Gooseneck Hitch
- Q&A: Recommended Brake Assemblies for a AL-KO/Hayes Axle
- Q&A: Recommended Brake Assemblies for a 80s Horse Trailer
- Q&A: Will the Dexter 23-105-106-09 Fit AL-KO 5200k Axles
- Q&A: Ensuring Trailer Hub Bearing Race Is Seated Properly Before Hub Installation
- Q&A: What Brand of Bearings Does etrailer hub part # AKHD-655-35-K Use
- Q&A: Who Makes Your Bearings?
- Q&A: What Brands of Bearings are Available



