Replacement Bearings and Seal for Lippert 5,200 lb Axle NOSP-OS-L-65516-7225-30PT

Question

Question:

I have a lippert 5200 axels ll152-sb-86-68.5- nosp—os-l-65516-7225-30pt what inner bearings and seals do I need

asked by: Gale

0

Expert Reply:

According to my research the correct replacement bearings are parts # 25580 and # LM67048 with the replacement seal being part # GS-2250DL. These are available in the Bearing Kit # BK3-300.

Just make sure that you have these bearings and that your seal has a 2.250" inner diameter and you're good to go! If it measures smaller than 2.250" then you need kit # BK3-310 which has the seal # GS-2125DL that has a 2.125" inner diameter.

expert reply by: Jon G

0

Answer 1

Hi Craig; thank you for providing those part numbers. That is the 2.25" inner diameter grease seal so for replacement bearings you can use the Bearing Kit, LM67048/25580 Bearings, 10-36 Seal #BK3-300 you were looking at. If you prefer Timken…

view full answer...

Answer 2

Thank you for the information. I reached out to my contact at Lippert and the correct replacement bearing kit for your LCI EZ Lube axle is part #BK2-100 which is for the standard #84 spindle. Attached is an installation video of this bearing kit for…

view full answer...

Answer 3

Yes, it will! The grease seal in the Bearing Kit item #BK3-100 has a 2.250" ID and a 3.376 OD.

view full answer...

Answer 4

Bearing Kit #BK3-100 consists of bearings 15123 and 25580, matching races, grease seal and cotter pin. This kit is intended for a 6K axle. The same component parts are found in Lippert bearing kit 333950, also rated for a 6K axle. Two helpful…

view full answer...

Answer 5

Hey Allen! Thank you for providing your axle information. According to Curt, the correct kit is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you need anything else don't hesitate to reach out in the comments below.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Replacement Bearings and Seal for Lippert 5,200 lb Axle NOSP-OS-L-65516-7225-30PT

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching