Replacement Rear Wheel Assembly for Yakima HoldUp Bike Rack

Question

Question:

My Yakima holdup black mode 2 inch hitch was rear ended by a car - this has bent the rear support arm. Do you have a replacement arm only rest of the assembly is OK. Please advise details. Thanks.

asked by: Noriel D

0

Expert Reply:

I'm sorry to hear that you were hit by a car (hopefully you're ok!) and we do have exactly what you need, though the arm by itself is not something that is available from Yakima as a replacement part.

For your Yakima HoldUp 2-Bike Rack # Y02443 you will need the Replacement Rear Wheel Assembly for Yakima HoldUp Bike Carriers # 8890281.

Just in the interest of thoroughness (because front and rear can be confusing on bike racks) I did add a photo showing the difference between the Rear and Replacement Front Wheel Assembly # 8890280.

expert reply by: Kyle S

0

click to enlarge

Answer 1

It truly depends on what bike rack you have and what key code you have with the locks. If the key you have doesn't turn the lock, it most likely is not the correct key for the rack. The best way to proceed is to make sure the key you have matches…

view full answer...

Answer 2

It looks like you have the standard version, the Yakima HoldUp #Y02443. The replacement front arm #8880833 is only for the HoldUp EVO #Y02479 bike rack. You are correct that in your case, you will need to replace the entire front wheel assembly…

view full answer...

Answer 3

I may have a solution for you, but the #8880832 isn't going to fit into the end on your Yakima HoldUp with a 2" shank; it may look like you could get it into the end but there's not a hole for a pin to be installed even if it did fit, so…

view full answer...

Answer 4

Hey Mike, We do have replacement keys for your Yakima HoldUp Bike Rack #Y02443. What is the number on your lock cores? It would have been on the face of the keys you received and written down on the instructions once you received the rack. If you can…

view full answer...

Answer 5

Since you have a Yakima Evo HoldUp the correct replacement rear tray would be the part #8880832.

view full answer...

Answer 6

Hello Peggy, thanks for reaching out. The only way we can provide the correct key would be if you have the key number. Without that, there is no way of knowing what key will open your lock. If the locks are currently unlocked, you can use the change…

view full answer...

Answer 7

I did some research and it appears that the numbers you gave go to the Yakima HoldUp Bike Rack for 2 Bikes #Y02443. With that being said, since you're needing to replace a broken arm you are actually going to need to replace the entire wheel…

view full answer...

Answer 8

The Yakima HoldUp 2 Bike Rack for 2" Hitches - Platform Style - Tilting #Y02443 is different from the Yakima HoldUp EVO 2 Bike #Y02479 in a couple ways. The original could hold bikes up to 60 lbs each versus the EVO holding up to 50 lbs per…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Rear Wheel Assembly for Yakima HoldUp Bike Rack

Products Featured in This Question

Continue Researching