Moving Trailer Hitch and Wiring From 2009 Toyota Venza to 2011 Toyota Venza

Question

Question:

Hi there, I have a 2009 Toyota Venza and am switching the hitch to my newer 2011 Toyota Venza. Can you please tell me what size of bolts are needed? I should purchase new ones rather than recycling the old. As well, will my older wiring kit for the 2009 fit the 2011? The 2009 was perfectly set up to plug and play. Thanks in advance!

asked by: BERNARD E

0

Expert Reply:

Your Draw-Tite Class III Max Frame Receiver Hitch # 75663 does fit both the 2009 and 2011 model Toyota Venza. You will definitely want to use new hardware for installation and the easiest route to take for this is to order part # RHK. Once on this product page simply type the part number in the text box provided (75663) and select Draw-Tite from the manufacturer drop-down menu. We will then send out the complete hardware kit for this particular hitch on your vehicle.

The hardware for this hitch includes six M10-125 x 40mm CL 10.9 hex bolts, six 3/8 inch conical toothed washers, and two 5/16 inch x 1 inch x 1-1/2 inch spacer blocks.

Both custom plug-and-play trailer wiring harnesses available for the 2009 Toyota Venza, the Tekonsha # 118482 and the Curt # C56079, also fit the 2011 model Venza so your existing kit will carry over without issue as well.

expert reply by: Chris R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Moving Trailer Hitch and Wiring From 2009 Toyota Venza to 2011 Toyota Venza

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching