Hitch Pin and Hitch Lock Recommendation for Yakima Holdup

Question

Question:

We have the Yakama holdup rack.

asked by: Michael R

0

Expert Reply:

It sounds like you are looking for a locking hitch pin lock for a Yakima hitch bike rack. If you can let me know what bike rack you have I can give you the exact hitch lock for your bike rack as recommended by Yakima. I can't recommend the use of the Kuat with a Yakima rack.

expert reply by: Jameson C

0

Michael R.

6/7/2019

We have the Yakama holdup rack.

Jameson C.

6/7/2019

What you would need for a hitch lock is the replacement hitch pin part # Y8890200 and then the hitch lock part # Y07235 and you'd have a locking hitch pin for your Yakima Holdup.

Answer 1

I checked with Yakima and for their Fourtimer bike rack part #Y02469 the correct hitch bolt is the part #8890260 and then for the matching lock assembly you'd need the #8820048.

view full answer...

Answer 2

For the Yakima FourTimer, you'd use the #Y8890200 anti-rattle hitch bolt. I've confirmed this with Yakima.Y8890200

view full answer...

Answer 3

We do have what you need but I checked with Yakima for you and the part you mentioned will not work with a Yakima FourTimer bike rack. Instead, there are a couple of parts you that you need, and I verified this with Yakima for you: - Replacement…

view full answer...

Answer 4

The Yakima Replacement Mounting Hardware part #Y8880129 is the replacement bolt you want for your Yakima Fourtimer part #Y02469.

view full answer...

Answer 5

For the Yakima Fourtimer #Y02469 the part number for the replacement hitch bolt is #Y8890200 and the retainer/nut is part #Y90254.

view full answer...

Answer 6

Replacement Threaded hitch pin #Y8880129 is indeed longer than the original bolt. It is 4.28 inches long overall. Something that you should know though is that when using a hitch adapter like you mentioned it reduces the tongue weight capacity of the…

view full answer...

Answer 7

I believe you are referring to the Yakima HoldUp #Y02443. If you need just the HitchLock alone, that is the #Y07235. However, if you need the hitch pin that is compatible with both the HitchLock and the HoldUp itself, that is the #Y8890200.

view full answer...

Answer 8

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt and is the same bolt that comes with the part #8890260. The size wrench you would use to install or remove this bolt is 15/16…

view full answer...

Answer 9

The Yakima replacement Ed Cap #Y8890283 will fit both 1-1/4-inch and 2-inch versions of their Hold Up bike rack #Y02445. The part of the racks where this installs is the same size. I confirmed this with my contact at Yakima.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Hitch Pin and Hitch Lock Recommendation for Yakima Holdup

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching