Gear Repair Kits for Venture Landing Gear Legs on 2007 Keystone Cougar

Question

Question:

Will this gear repair kit work for a 2007 Keystone Cougar with Venture landing gear?

asked by: Robert B

0

Expert Reply:

Yes, the Follow Jack Repair Kit # LG-146060 that you referenced does work with the Venture landing gear leg you have on your 2007 Keystone Cougar. This is a repair kit for the follower leg. If instead you need a kit for a lead leg you'd want the part # LC146059.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I linked the schematic diagram for Lead Jack Repair Kit #LG-146059 taken from the written instructions. The complete instructions will be sent to you in a separate link. The follow leg repair kit is part #LC146060 in case you need it.

view full answer...

Answer 2

The landing gear looks like a standard set based on the pictures and the dimensions you listed. The part #LC146060 would be what you need for the follow leg and then part #LC146059 for the lead leg.

view full answer...

Answer 3

Though I could not find anything about the T46059 repair kit you referenced, but odds are the jack isn't rated high enough for the weight of your trailer. Or there is more than just the gears that need to be replaced. What you will probably want…

view full answer...

Answer 4

Thanks for the pictures! Based on the part number of your motor it appears you have Venture landing gear. As such you will likely need follow leg rebuild kit #LC146060 or lead leg rebuild kit #LC146059 to fix your landing gear. Landing gear legs are…

view full answer...

Answer 5

Are you looking for installation instructions for a particular trailer vent or for the ceiling garnish, #VA0445-26? Ventline does not offer instructions just for the garnish because it is basically an interior trim piece that slides around the vent…

view full answer...

Answer 6

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Gear Repair Kits for Venture Landing Gear Legs on 2007 Keystone Cougar

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching