Grease Maintenance Schedule For Lippert Ground Control 3.0
Updated 12/01/2025 | Published 07/12/2022 >
Products Featured in This Question
Question:
Does the Hall Effect Motor ever need to have grease added?
asked by: John H
Expert Reply:
No, the hall effect motor does not have to be greased, but per the service manual if the jacks are down for an extended period, it is recommended to spray the exposed leveling jack tubes with lubricant every 3 months for protection. If you live in a salty environment it is recommended to spray the rods every month.
I spoke to my contact at Lippert and they told me that The White Lithium Grease # L11354 can be used on the gears, but do not over grease them. Using to much grease will start to attract dirt and debris to the leg.
I attached a review video link below.
Product Page this Question was Asked From
Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Search Results: landing gear
- Search Results: lippert ground control 30
- Search Results: 5th wheel front landing gear
- Search Results: lippert~landing~gear
- Search Results: lippert 122096
- Search Results: camper jacks
- Q&A: Replacement Front Jack for Lippert Ground Control 3.0 Leveling Systems
- Video: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System Review
- Video: Review of the Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Q&A: Replacement Front Jack for Lippert Ground Control 3.0 Leveling Systems
- Shop: etrailer Hydraulic Trailer Jack - Square Tube - External Pump - 20" Lift - 8K lbs - Direct Weld
- Q&A: Right Rear Leg/Awning Side for a Lippert Ground Control 3.0 Electric Leveling System
- Search Results: rv water inlets accessories and parts
- Shop: Easy Grease Trailer Hub and Drum Assembly for 5.2K - 7K Axles - 12" - 8 on 6.5 - Pre-Greased
- Video: All About the Replacement 24-1/2" Left Rear Leg
- Video: Ultimate Overview of the Replacement 24-1/2" Right Rear Leg
- Q&A: Wiring Diagram for Replacement Left Rear Leg for Lippert Ground Control 3.0
- Shop: Replacement 24-1/2" Right Rear Leg - Lippert Ground Control 3.0 Electric Leveling System
- Q&A: Lippert Ground Control 3.0 Replacement Front Jacks
- Q&A: Troubleshooting Lippert Landing Gear Lead Leg Not Fully Retracting
- Shop: Replacement Thrust Bearing for Dutton-Lainson Jacks - 1.248" to 1.257" Outer Diameter
- Shop: Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Shop: Repair Service Kit for Lippert Power Gear Leveling Systems - 16K Jack
- Q&A: Will Replacement Front Jack for Lippert Ground Control 3.0 System Work On 2021 Open Range 5th Wheel?
- Video: Review of etrailer Trailer Bearings Races Seals Caps - Bearing Kit - BK3-200
- Video: Review of etrailer Trailer Bearings Races Seals Caps - Bearing Kit - BK3-210
- Video: All About the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Article: Fifth Wheel Trailer Hitch Information and Installation Tips



Dennis
11/29/2025
I have a zerk fitting on mine, does it need to be serviced and what type grease should be used.