Does Curt Trailer Wiring Install Harness for 2019 Honda CR-V Require Separate Ground Wire

Question

Question:

is the ground wire in with the plug or does in it need a seperate screw to ground

asked by: Patrick P

0

Expert Reply:

The install of the Tekonsha kit part # 118741 that you referenced does require the a separate ground wire get attached to the vehicle but the Curt harness part # C56370 for your 2019 Honda CR-V does not require this extra wire. It ground through the plug that attaches to the vehicle. I attached an install video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

It depends on a few things as it's not a standard difference but typically an incandescent 1157 will pull around 2 amps whereas an LED like the part #CM93236 pulls around 0.2 amp.

view full answer...

Answer 2

Other than the higher amperage rating offered by the Tekonsha #118741, there isn't much in the way of differences between it and the Curt #C56370. Both use solid state construction, the Curt uses the SMT which doesn't use through-holes in the…

view full answer...

Answer 3

Yes, you are correct. The Curt Trailer Hitch item #C13397 is the correct hitch for the 2023 Honda CR-V Hybrid. The wiring harness is going to depend on whether or not your CR-V is front wheel drive or all wheel drive. I have listed both options…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does Curt Trailer Wiring Install Harness for 2019 Honda CR-V Require Separate Ground Wire

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching