Replacement Clearance Lights for 2007 Featherlite Trailer 8127

Question

Question:

Have a 2007 featherlite 8127. I need clearance lights. Do I just get the lense or do I need the whole assembly. One 4 inch red will need whole assembly. But the 2 amber fender lights are out 2 inch and 4 of the amber upper clearance lights are out or partially out.

asked by: Melissa B

0

Side Amber Clearance Light on 2007 Featherlite Trailer
(click to enlarge)

Light Base on 2007 Featherlite Trailer
(click to enlarge)

ID Tag on 2007 Featherlite Trailer
(click to enlarge)

Fender Light on 2007 Featherlite Trailer
(click to enlarge)

Expert Reply:

Hey Melissa, thanks for reaching out!

It looks like you have the Optronics Thinline lights on your Featherlite trailer so you'll need the following:

Red
- 2" # AL91RB
- 4" # MCL75RB

Amber
- 2" # AL91AB
- 4" # MCL65AB

Which ones are you needing the whole assembly for?

expert reply by: Jon G

0

Mel

2/3/2025

Need one 4 inch red and one 4 inch amber

Reply

Jon G.

2/3/2025

@Mel Thanks for the feedback! For red we have # MCL67RBCB and for amber we have # MCL67ABCB. These have chrome bases, but they're small enough that it shouldn't be noticeable if your other ones are black.

Reply

Answer 1

Hello Kurt, I can definitely help you out with the right clearance and side markers for your 6 x 12 dump trailer. I attached an image to reference for the lights/reflectors, these are the DOT requirements: - Rear reflector (#4 on diagram) 2 of the…

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 3

Hello Andrew. It looks like our installers have not had the privilege of doing an install on a 2025 Chevy Equinox. I see that the wiring harnesses that we do have in stock have the 6 pin connector. It looks like Curt is aware of this issue and is in…

view full answer...

Answer 4

The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this you'd need the part #A46PB and then for a grmmet part…

view full answer...

Answer 5

We actually have the Brake Buddy 32220 reverse solenoid available with the Titan Solenoid Valve Replacement Kit #TK71-755-00. The solenoid itself would be an exact replacement and it features the two mounting holes at the bottom like you described…

view full answer...

Answer 6

Hey Brian, For inner bearing #15123 you would need race #15245 and for outer bearing #25580 you would need race #25520. The grease seal can be purchased with part #GS-2250DL. The Timken Bearing Kit #TMK42VR would include 15123/25580 Bearings,…

view full answer...

Answer 7

The Demco Hydraulic Brake Actuator part #DM72VR is a great option to replace an Atwood 82543. That said, it does not come with any sort of reverse lockout feature therefore in order to reverse without the brakes locking up you will either need to add…

view full answer...

Answer 8

For the clearance light part #AL91RB we have the grommet part #A91GB which is basically a hard rubber.

view full answer...

Replacement Clearance Lights for 2007 Featherlite Trailer 8127

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching