Wall Thickness of Curt Hitch Extension and Reducer # C45048

Question

Question:

what is the thickness of the walls or the gauge?

asked by: Johnny B

0

Expert Reply:

The wall thickness of the Curt Hitch Extension and Reducer # C45048 is 1/4 inch.

expert reply by: Jameson C

0

Answer 1

Hey Gary. I checked the manual for your RVP 8000 unit. If you're sure its getting around a 115 volts then I do agree it sounds like a capacitor has gone bad. Unfortunately I do not have a replacement one for you. The only thing I have to offer is…

view full answer...

Answer 2

TorkLift doesn't have their instruction manuals posted online so I'm unable to find the exact step by step instructions, but I was able to find a video where Shane will walk you through installing a similar front mounted tie-down model to…

view full answer...

Answer 3

The TorkLift Custom Frame-Mounted Camper Tie-Downs part #TLD2132 for your 2018 Ram 3500 do not use any pre drilled holes in the frame rail nor do they require any drilling. These are a unique set of camper tie-downs in that they use hooks to sandwich…

view full answer...

Answer 4

Are you asking about a slide out awning/topper or an actual cover? I am going to assume you mean topper since that's a common thing people look for. We don't have the dimensions of what your Lance would have but here are a few common options:…

view full answer...

Answer 5

Yes, trailer tires are rated by tire. So for example, the Kenda 4.80/4.00-8 Load Range C Tire, part #AM10004, is rated up to 745 pounds at 90 psi. Two tires on one axle are rated up to 1,490 pounds. You still need to verify the weight capacity of the…

view full answer...

Answer 6

The Curt Combo Bar with 2" Trailer Hitch Receiver #C49360 is made of solid raw steel. It is made in the USA and this unit is equipped with a 1/2" reinforcing collar for extra strength and has a raw finish to be ready for welding. The…

view full answer...

Answer 7

It sounds like you are asking about connecting the breakaway switch of the Brake Buddy Classic 3 Portable Supplemental Braking System #HM39494. I cut out some pages from the instruction manual for you to check out, but what you'll do is actually…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Wall Thickness of Curt Hitch Extension and Reducer # C45048

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching