Replacement Gears for etrailer.com and Ram Square A-Frame Jack TJDA-5000S

Question

Question:

Do you sell a replacement gear kit for TJD or TJDA-5000S kits? Will the kit for TJA-5000 jacks fit TJD?

asked by: Matthew C

1

Helpful Expert Reply:

I reached out to my tech contact and confirmed that the Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs # TJD-7000S-GR is the same gear kit used in the Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 3,000 lbs # TJDA-5000S. I've attached videos of each to assist.

expert reply by: Jason S

1

Answer 1

That is a custom trailer build I believe. I asked another Expert here and neither of us have seen anything like it. Since you are adding a plate to the top and bottom of your tongue, the Bulldog Jack Support Plate - A-Frame - 2.3" Square Hole…

view full answer...

Answer 2

The lifting capacity of this jack is determined by the drop leg. In this case the Drop Leg #TJD-5000-FT that comes on the #TJDA-5000S jack is rated for a 3,000 lb lift capacity. If you are needing a trailer jack that has a 5,000 lb lift capacity then…

view full answer...

Answer 3

Yes, the leg foot plate part #JF-1005H-Z does fit the Ram Sidewind jack part #TJA-5000S-B.

view full answer...

Answer 4

I do not recommend installing an a-frame jack in a manner that requires you to disassemble it. What I do suggest, since you have fabrication capabilities, is that you make a new a-frame jack mounting point on the trailer at the height you want it and…

view full answer...

Answer 5

I checked and although there is not a bushing for the Bulldog Swivel Jack - Topwind #BD178101, we do have a 5,000 lb Bulldog A-frame jack with a short retracted height that is going to be exactly what you need. The Round A-Frame Trailer Jack -…

view full answer...

Answer 6

I just went out to the warehouse and checked. The Drop Leg for etrailer and Ram Jacks Footplate item #JF-1005H-Z fits perfectly with the etrailer A-Frame Round Jack item #TJA-5000S-B.

view full answer...

Answer 7

I spoke to my contact at Pacific Rim, they said the correct replacement lower flange bushing and washer for your 8,000 lb Ram jack will be the Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks - 7K…

view full answer...

Answer 8

The etrailer.com Round A-Frame Trailer Jack #TJA-5000S-B that you referenced does not include a footplate. This is actually not all that uncommon, as it simply allows you to choose the type of base you want (footplate or caster wheel) or use a base…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Gears for etrailer.com and Ram Square A-Frame Jack TJDA-5000S

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching