How to Determine What Trailer Jack Would Attach to Welded on Frame Bracket

Question

Question:

how do I know what jack to get. the bracket is welded to the trailer and I think I only want to replace the jack and use the existing bracket. I think it will bolt on with the center bolt only.

asked by: Rick J

0

Expert Reply:

If you can get me a picture of the bracket you have welded to your trailer I can most likely identify what jack would bolt to it. For example if your bracket looks like the one I attached a picture of the Fulton jack part # FXP15W would fit and work well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey George, best solution for you will be to go with an all new jack like the etrailer part #e95YV because Fulton is no longer in business so there isn't a way to get a replacement F2 and none of the other jacks out there use the same bolt…

view full answer...

Answer 2

Hey Gary, the max PSI of the Aluminum Trinity Series Trailer Wheel #TA74XR is well over 100 psi and this is limited by the valve stem that it has and not the wheel. The included valve stem and wheel could easily handle the PSI requirements of…

view full answer...

Answer 3

I spoke to my contact at Fulton and he said the correct replacement spring for the ratchet of your Fulton F2 winch is the part #4769-28. I attached a picture that shows a diagram for the winch for you to check out. You will be able to see how the…

view full answer...

Answer 4

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 5

Hey Jack, I looked up your Cobalt 246 and I would say it's large enough that you would want the 60 inch guide ons like the part #CE27646 that you referenced. You can also go out to your trailer and measure 40 and 60 inches up from the frame to…

view full answer...

Answer 6

How did your jack attach to its mounting bracket? Is that the single bolt that you mentioned? If so then the only option we have that could work is Fulton jack #F1411300301 which normally uses mounting bracket #P9012-00. And the replacement hardware…

view full answer...

Answer 7

What would work as a replacement for your Fulton 1,200 lb jack that I would recommend is the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301. In your pictures you did not include one that shows the bracket that attaches to your trailer mount,…

view full answer...

Answer 8

I took a look at the installation instructions for the Fulton Bolt-Thru Swivel Marine Jack part #FXP15W and there isn't any sort of torque spec for the center bolt but what is stated is that you will need to tighten the lockout until there is…

view full answer...

Answer 9

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 10

The Fulton Bolt-Through Swivel Jack, part #F1411300301 will allow you to use the existing bracket welded to your trailer frame. The jack has a 1500 lb lift capacity, so if your trailer's tongue weight is less than that amount, it'll work…

view full answer...

Answer 11

The Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 does not come with the bolt-thru swivel bracket you will need to attach it to the trailer. For this, you can use the part #P9012-00. The plate that you are referring to will attach to the above…

view full answer...

Answer 12

In terms of a direct replacement for the same mounting method as your Bulldog #BD154107, you'll want to use the Fulton #FXP15W . which will bolt on to your existing welded on jack mount and comes with a wheel. The main difference between these…

view full answer...

How to Determine What Trailer Jack Would Attach to Welded on Frame Bracket

Continue Researching