Is the Mounting Bracket Included with the Fulton Bolt-Thru Swivel Marine Jack Part # FXP10W0301

Question

Question:

So I plan to buy the weld on from you. its $ but shipping ($) brings by up to $. At that point I would certainly just buy this (FXP15W) for $, and not have to do any grinding or welding. Im not even sure if I would buy with free shipping to save the $ and have to grind/weld. But I may. Can you offer free shipping on this?

asked by: Anthony

0

Expert Reply:

The Fulton Bolt-Thru Swivel Marine Jack part # FXP10W0301 does not come with the bolt-thru swivel bracket you will need to attach it to the trailer. For this, you can use the part # P9012-00. The plate that you are referring to will attach to the above bracket. As you mentioned, you will need to cut/grind the old bracket off and weld the new one on in order to use this jack.

I have attached a review video of the jack for you as well.

expert reply by: Conner L

0

Anthony

5/3/2018

So I plan to buy the weld on from you. its $ but shipping ($) brings by up to $. At that point I would certainly just buy this (FXP15W) for $, and not have to do any grinding or welding. Im not even sure if I would buy with free shipping to save the $ and have to grind/weld. But I may. Can you offer free shipping on this?

Conner L.

5/3/2018

The Fulton Bolt-Thru Swivel Marine Jack part # FXP15W (1,200 lbs) that you referenced is the same jack as the Fulton Bolt-Thru Swivel Marine Jack part # FXP10W0301 (1,500 lbs) for the exception of the weight capacity. You would still need to use part # P9012-00 to attach either jack to your trailer. If you do not want to cut and reweld a new bracket onto the trailer then you an use a bolt-on style jack like the Fulton Bolt-Thru Swivel Marine Jack part # FXP10 for 1,200 lb capacity or part # FXP15 for 1,500 lb capacity. These jacks will bolt onto 3" x 3", 3" x 4", or 3" x 5" trailer frames. Unfortunately, we can only offer free shipping on orders that exceed $99. I have attached a review video on one of the bolt-on jacks for you below.

Answer 1

To replace your older Fulton Magnum Series 1500 Pound Jack, I recommend the Fulton Bolt-Thru Swivel Marine Jack #FXP15W. This 1,500 pound swivel jack is what Fulton replaced the Magnum Series with, so it should use the same mounting design as your…

view full answer...

Answer 2

I took a look at the installation instructions for the Fulton Bolt-Thru Swivel Marine Jack part #FXP15W and there isn't any sort of torque spec for the center bolt but what is stated is that you will need to tighten the lockout until there is…

view full answer...

Answer 3

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 4

The Fulton Bolt-Through Swivel Jack, part #F1411300301 will allow you to use the existing bracket welded to your trailer frame. The jack has a 1500 lb lift capacity, so if your trailer's tongue weight is less than that amount, it'll work…

view full answer...

Answer 5

Most likely the #FXP15W would work great as a replacement for what you have but it's hard to verify that without seeing how what you have now mounts to the trailer. If you could send me a picture of what you have I can verify.

view full answer...

Answer 6

What would work as a replacement for your Fulton 1,200 lb jack that I would recommend is the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301. In your pictures you did not include one that shows the bracket that attaches to your trailer mount,…

view full answer...

Answer 7

In terms of a direct replacement for the same mounting method as your Bulldog #BD154107, you'll want to use the Fulton #FXP15W . which will bolt on to your existing welded on jack mount and comes with a wheel. The main difference between these…

view full answer...

Answer 8

How did your jack attach to its mounting bracket? Is that the single bolt that you mentioned? If so then the only option we have that could work is Fulton jack #F1411300301 which normally uses mounting bracket #P9012-00. And the replacement hardware…

view full answer...

Answer 9

If you can get me a picture of the bracket you have welded to your trailer I can most likely identify what jack would bolt to it. For example if your bracket looks like the one I attached a picture of the Fulton jack part #FXP15W would fit and work…

view full answer...

Answer 10

Hi Stacy; we still carry the Fulton Boat Trailer Jack w/ Wheel #FXP100W0301 so you can order the exact same jack. I see you looked at a few others so if this is not the jack you were referring to please let me know in the comments below.

view full answer...

Answer 11

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 12

Both hitches made for your 2004 Lexus GX 470, Draw-Tite #75155 and Curt #13445, are welded together as one-piece so I think what you are looking for is actually a 2-inch ball mount that slides into the square receiver opening and lets you tow. This…

view full answer...

Is the Mounting Bracket Included with the Fulton Bolt-Thru Swivel Marine Jack Part # FXP10W0301

Featured Help Information

Miscellaneous Media

Continue Researching