Determining Correct Curt Class V Trailer Hitch for 2002 Chevy Silverado to Replace Factory Hitch
Updated 03/21/2019 | Published 03/20/2019
Products Featured in This Question
Question:
Hello, I have a 2002 Chevy 3500 pick up with the factory POS hitch that is rusting out. The factory hitch bolts to the stock rear bumper. Will the C15132 work or would I need the C15313? Thanks!
asked by: Bob C
Helpful Expert Reply:
If your 2002 Chevy Silverado 3500 features the standard factory rear bumper (and not a 10 inch deep drop bumper) then the correct Curt hitch is the Class V # C15312 that you referenced. I have attached an image that shows the difference between a standard and deep drop bumper that you can use for reference if you're unsure.
If you find that you have the deep drop bumper then you will want to go with part # C15313, which features longer brackets so the receiver can sit below the taller bumper.
Both hitches will use existing holes in the truck's frame for a no-drill installation. Their superior black powder coat will do a great job of resisting corrosion over time so you don't run into the same issues you're having with the factory hitch.
Just looking through pictures customers sent in who purchased this hitch it appears you are not alone in having to replace the factory model due to severe rust. I have attached the written installation instructions that you can check out as well.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Trailer Hitch
- For Towing
- Class V
- 2400 lbs TW
- 16000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Search Results: 41944
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: How to Choose a Trailer Brake Controller
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Article: How to Measure for Trailer Hitch Drop
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Search Results: trailer jack
- Video: Clean Up Your Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Search Results: trailer hitch ball mount
on Trailer Hitch
